Lexmark C782 IPDS Printer and Host Setup Guide - Page 40

Address, Netmask, Gateway, Enable DHCP, Enable RARP, Enable BOOTP, AutoIP, WINS Server Address, DNS

Get Lexmark C782 PDF manuals and user guides View all Lexmark C782 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 40 highlights

IPDS Printer and Host Setup Guide PSF/2 LAN Printing Using an Internal LAN Print Server TCP/IP Settings Parameter Value Address 157.184.67.102 (Address available from your network administrator) Netmask 255.255.255.0 (Appropriate netmask for your network) Gateway 157.184.67.1 (IP address of your IP gateway) Enable DHCP On or Off (On, if you use a DHCP server.) (Off, if you set the IP address another way.) Enable RARP On or Off (On, if you use a RARP server.) (Off, if you set the IP address another way.) Enable BOOTP On or Off (On, if you use a BOOTP server.) (Off, if you set the IP address another way.) AutoIP On or Off (Default is On. This is the recommended setting.) WINS Server Address 157.184.100.20 (Address of your WINS Server) DNS Server Address 157.184.115.7 (Address of your DNS Server) 6 Save/submit any changes and return to the Ready screen. 7 To verify the new print server settings, print a Network Setup Page. Using the control panel MENU/Menus, select Reports > Network Setup Page. This can be Network Setup Page, Network 1 Setup Page, or Network 2 Setup Page. Note that the Network Job Timeout is identified as End-of-job Timeout on this report. Step 5 Configure the Printer's Network Job Timeout Note: If you specified Port 5001 or 9600 as the TCP/IP port number in the printer created in Step 2 [page 36], you do not need to configure the printer's Network Job Timeout. Go directly to Step 6 [page 41] . Important! If you specified Port 9100 as the TCP/IP port number, the printer's Network Job Timeout must be manually disabled by setting it to "0" (or to "Disable"). This is necessary to allow the host's Release Timer value or the printer's IPDS Timeout value to control when print jobs from another protocol, interface, server, or host can be started. It also prevents the printer from ending the IPDS session if communication is delayed between the host and printer. Additional information on the printer IPDS Timeout value may be found in the IPDS Emulation User's Guide. Follow these steps to disable the printer's Network Job Timeout from the control panel: 40

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
40
IPDS Printer and Host Setup Guide
PSF/2 LAN Printing Using an Internal LAN Print Server
6
Save/submit any changes and return to the
Ready
screen.
7
To verify the new print server settings, print a Network Setup Page. Using the control panel
MENU/Menus
,
select
Reports > Network Setup Page
. This can be
Network Setup Page
,
Network 1 Setup Page
, or
Network 2 Setup Page
. Note that the
Network Job Timeout
is identified as
End-of-job Timeout
on this
report.
Step 5
Configure the Printer’s Network Job Timeout
Note:
If you specified Port 5001 or 9600 as the TCP/IP port number in the printer created in Step
2 [page36]
,
you do not need to configure the printer’s Network Job Timeout. Go directly to Step
6 [page41]
.
Important!
If you specified Port 9100 as the TCP/IP port number, the printer’s
Network Job Timeout
must be
manually disabled by setting it to "0" (or to "Disable"). This is necessary to allow the host’s
Release Timer
value or the printer’s
IPDS Timeout
value to control when print jobs from another protocol, interface, server, or
host can be started. It also prevents the printer from ending the IPDS session if communication is delayed
between the host and printer.
Additional information on the printer IPDS Timeout value may be found in the IPDS Emulation User’s Guide.
Follow these steps to disable the printer’s
Network Job Timeout
from the control panel:
Address
157.184.67.102
(Address available from your network administrator)
Netmask
255.255.255.0
(Appropriate netmask for your network)
Gateway
157.184.67.1
(IP address of your IP gateway)
Enable DHCP
On
or
Off
(On, if you use a DHCP server.)
(Off, if you set the IP address another way.)
Enable RARP
On
or
Off
(On, if you use a RARP server.)
(Off, if you set the IP address another way.)
Enable BOOTP
On
or
Off
(On, if you use a BOOTP server.)
(Off, if you set the IP address another way.)
AutoIP
On
or
Off
(Default is On. This is the recommended setting.)
WINS Server Address
157.184.100.20
(Address of your WINS Server)
DNS Server Address
157.184.115.7
(Address of your DNS Server)
TCP/IP Settings
Parameter
Value