Lexmark X560n Clearing Jams Guide
Lexmark X560n Manual
 |
View all Lexmark X560n manuals
Add to My Manuals
Save this manual to your list of manuals |
Lexmark X560n manual content summary:
- Lexmark X560n | Clearing Jams Guide - Page 1
• Do not use paper that has been cut or trimmed by hand. • Do not mix paper sizes, weights, or types in the same stack. • Store the paper in an appropriate environment. • Do not remove trays while the printer is printing. • Push all trays in firmly after loading paper. • Make sure the guides in the - Lexmark X560n | Clearing Jams Guide - Page 2
3 Remove any jammed paper from inside the printer. 4 Close the front door. 2 - Lexmark X560n | Clearing Jams Guide - Page 3
handle, and pull Tray 1 out. Remove the tray completely. 6 Remove any jammed paper from inside the tray housing. Clearing Tray 2 jams If the paper did not feed from Tray 2 correctly, the jam is in the tray. Jam at Tray 2 appears. 1 Grasp the handle, and pull Tray 1 out. Remove the tray completely - Lexmark X560n | Clearing Jams Guide - Page 4
of paper lying on top of the stack. Pull it straight out. • Jams behind the tray area-Locate the jam on the bottom surface of the tray housing. You may have to reach far under the printer to locate the jam, as shown in the following illustration. Pull the jam straight out. 3 Align - Lexmark X560n | Clearing Jams Guide - Page 5
paper from inside the printer. 6 Close the front door. • Jams in the tray-Locate the single piece of paper lying on top of the stack. Pull it straight out. Clearing Tray 3 jams If the paper did not feed from Tray 3 correctly, the jam is in the tray. Jam at Tray 3 appears. 1 Grasp the handle - Lexmark X560n | Clearing Jams Guide - Page 6
-Locate the jam on the bottom surface of the tray housing. You may have to reach far under the printer to locate the jam, as shown in the following illustration. Pull the jam surface to cool before touching it. 5 Remove any jammed paper from inside the printer. 3 Align the tray, and insert it. 6 - Lexmark X560n | Clearing Jams Guide - Page 7
6 Close the front door. CAUTION-HOT SURFACE: To reduce the risk of injury from a hot component, allow the surface to cool before touching it. 1 Push the release button, and gently lower the front door. 2 Lift the fuser pressure release levers to release tension on the paper. Clearing jams in the - Lexmark X560n | Clearing Jams Guide - Page 8
3 Lift the fuser cover, and then remove the jammed paper. 4 Close the fuser cover, and then lower the pressure release levers. 5 Close the front door. 8 - Lexmark X560n | Clearing Jams Guide - Page 9
, allow the surface to cool before touching it. 1 Push the release button, and gently lower the front door. 2 Pull out the jammed paper from the duplex unit. If jammed paper cannot be found, go to the next step. 3 Lift the transfer belt unit. 4 Remove any jammed paper from the - Lexmark X560n | Clearing Jams Guide - Page 10
5 Close the transfer belt unit. 6 Close the front door. Clearing jams in the ADF If the paper is jammed in the ADF, Jam at Scanner appears. Remove all jammed paper, and make sure the paper feed tray is not overfull. 1 Remove all paper from the paper feed tray, and then open the ADF cover. 10 - Lexmark X560n | Clearing Jams Guide - Page 11
2 If the jam is in the paper feed area, remove the jam by carefully pulling it up. 3 If the jam is at the paper exit area, turn the dial to remove the jam. 4 Close the ADF cover. 5 Open the scanner cover and remove any jammed paper from the paper feed area. 11 - Lexmark X560n | Clearing Jams Guide - Page 12
6 Close the scanner cover. 7 When all the jammed paper is removed, Return the Removed Original and Press Start appears. Place the original document in the ADF, and then press Start to continue with the scan job. 12
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
 |
 |
Lexmark™ X560
Clearing Jams Guide
Avoiding and clearing
jams
Avoiding jams
The following hints can help you avoid jams:
•
Use only recommended paper or specialty media.
For more information, see the
Card Stock & Label Guide
available on the Lexmark Web site at
www.lexmark.com/publications
.
•
Do not load too much paper. Make sure the stack height does
not exceed the indicated maximum height.
•
Do not load wrinkled, creased, damp, or curled paper.
•
Flex, fan, and straighten paper before loading it.
•
Do not use paper that has been cut or trimmed by hand.
•
Do not mix paper sizes, weights, or types in the same stack.
•
Store the paper in an appropriate environment.
•
Do not remove trays while the printer is printing.
•
Push all trays in firmly after loading paper.
•
Make sure the guides in the trays are properly positioned, and
are not pressing too tightly against the paper.
•
Make sure all printer cables are attached correctly. For more
information, see the setup documentation.
Understanding jam messages
and locations
Open doors and covers, and remove trays to access jam locations.
The illustration shows possible jam locations. To resolve any jam
message, you must clear all paper from the paper path.
Jam message
Area name
1
Jam at Exit
Open Door A
Fuser top
2
Jam at Reg. Roll
Open Door A
Fuser bottom
3
Jam at Duplexer
Open Door A
Lift Belt Unit
Optional duplex unit
4
Jam at Tray 3
Open Tray 3
Open Door A
Optional 550-sheet tray
(Tray 3)
5
Jam at Tray 2
Open Tray 2
Open Door A
Standard tray (Tray 2)
6
Jam at Tray 1
Check Tray 1
Open Door A
Multipurpose Feeder (Tray 1)
Jam message
Area name
7
Jam at Scanner
Open ADF Cover R
and Remove Paper
Turn the Green Dial
to Remove Paper
ADF tray
Clearing Tray 1 (MPT) jams
If the paper did not feed from the multipurpose feeder
correctly,
Jam at Tray 1
appears.
1
Pull the jammed paper out of the multipurpose feeder tray,
and then remove any remaining paper from the tray.
2
Push the release button, and gently lower the front door.
CAUTION—HOT SURFACE:
To reduce the risk of injury
from a hot component, allow the surface to cool before
touching it.
1