Lexmark X864 IPDS Printer and Host Setup Guide - Page 40

Problem 11: Disk Full or Flash Full, Problem 10: Disk Protected, Fonts Not Erased

Get Lexmark X864 PDF manuals and user guides View all Lexmark X864 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 40 highlights

IPDS Printer and Host Setup Guide Printer Messages and Problems B. Select Continue and the job will be printed. Note: The host is notified of the paper change. Several jobs may print formatted for the wrong paper size before the host changes to the new paper size. Problem 9: Standard Network port not working I have a Standard Network port and a MarkNet internal LAN print server installed. My Standard Network port is not working. Solution to Problem 9 The Standard Network port cannot be used when a MarkNet internal LAN print server is installed. Try the following. A. Obtain an unused network address from your administrator. B. Remove the MarkNet internal LAN print server. C. Use the new address and other information to configure the Standard Network port. D. Attach the Standard Network port to the network. E. Send a job to the printer. F. If the job does not print, you should recheck all settings on the printer and host. G. If the job prints, you must decide which port to use for receiving jobs. Problem 10: Disk Protected, Fonts Not Erased or Flash Protected, Fonts Not Erased One of the above messages is displayed when I select menu items under the Remove Resources Menu. Solution to Problem 10 The disk or the flash is password protected. Remove the password protection to remove the IPDS fonts and then restore the password protection. Problem 11: Disk Full or Flash Full The printer control panel displays a disk full or flash full message and the printer stops printing. Solution to Problem 11 The hard disk or user flash became full before all resources from the host were captured. Select Continue to resume printing. When the printer returns to Ready, disable capturing of resources. To disable capturing, select MENU/Menus > Option Card Menu > IPDS MENU > RESOURCE CAPTURE > Resources to Capture > Disable. If additional resources must be captured, install a larger user flash or hard disk. You may also choose to capture fewer resources, reformat the user flash or remove resources from the disk and capture the resources again. To remove resources from a disk, select MENU/Menus > Option Card Menu > IPDS MENU > RESOURCE CAPTURE > Remove Resources > All, Disk or Flash. 40

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
40
IPDS Printer and Host Setup Guide
Printer Messages and Problems
B.
Select
Continue
and the job will be printed.
Note:
The host is notified of the paper change. Several jobs may print formatted for the wrong paper size
before the host changes to the new paper size.
Problem 9:
Standard Network port not working
I have a Standard Network port and a MarkNet internal LAN print server installed. My Standard Network
port is not working.
Solution to Problem
9
The Standard Network port cannot be used when a MarkNet internal LAN print server is installed. Try the fol-
lowing.
A.
Obtain an unused network address from your administrator.
B.
Remove the MarkNet internal LAN print server.
C.
Use the new address and other information to configure the Standard Network port.
D.
Attach the Standard Network port to the network.
E.
Send a job to the printer.
F.
If the job does not print, you should recheck all settings on the printer and host.
G.
If the job prints, you must decide which port to use for receiving jobs.
Problem 10: Disk Protected, Fonts Not Erased
or
Flash Protected, Fonts Not Erased
One of the above messages is displayed when I select menu items under the
Remove Resources
Menu.
Solution to Problem
10
The disk or the flash is password protected. Remove the password protection to remove the IPDS fonts and
then restore the password protection.
Problem 11: Disk Full or Flash Full
The printer control panel displays a disk full or flash full message and the printer stops printing.
Solution to Problem
11
The hard disk or user flash became full before all resources from the host were captured. Select
Continue
to
resume printing. When the printer returns to
Ready,
disable capturing of resources. To disable capturing, select
MENU/Menus > Option Card Menu > IPDS MENU > RESOURCE CAPTURE > Resources to Capture >
Disable
.
If additional resources must be captured, install a larger user flash or hard disk.
You may also choose to capture fewer resources, reformat the user flash or remove resources from the disk
and capture the resources again.
To remove resources from a disk, select
MENU/Menus > Option Card Menu > IPDS MENU > RESOURCE
CAPTURE > Remove Resources > All
,
Disk
or
Flash
.