LiftMaster HCTDCU HCTDCU Installation Manual - Page 9

Installation, Save These Instructions.

Get LiftMaster HCTDCU PDF manuals and user guides View all LiftMaster HCTDCU manuals
Add to My Manuals
Save this manual to your list of manuals

Page 9 highlights

INSTALLATION IMPORTANT INSTALLATION INSTRUCTIONS TO REDUCE THE RISK OF SEVERE INJURY OR DEATH: 1. READ AND FOLLOW ALL INSTRUCTIONS. 2. Install operator ONLY on properly balanced and lubricated gate/ door. An improperly balanced gate/door may NOT reverse when required and could result in SEVERE INJURY or DEATH. 3. ALL repairs to cables, spring assemblies and other hardware MUST be made by a trained systems technician BEFORE installing operator. 4. Disable ALL locks and remove ALL ropes connected to gate/door BEFORE installing operator to avoid entanglement. 5. Install gate/door operator 8 feet (2.4 m) or more above floor. 6. NEVER connect operator to power source until instructed to do so. 7. Any openings shall be designed, guarded or screened to prevent a 2 1/4" (5.7 cm) diameter sphere from passing through the openings anywhere in the gate/door. 8. Entrapment protection devices MUST be installed to protect anyone who may come near a moving gate/door. Upon completion of installation, test entrapment protection device. 9. Too much force on gate/door will interfere with proper operation of safety reversal system. • NEVER increase force beyond minimum amount required to move gate/door. • NEVER use force adjustments to compensate for a binding or sticking gate/door. • If one control (force or travel limits) is adjusted, the other control may also need adjustment. 10. Install control station: • within sight of the gate/door • out of reach of children at minimum height of 5 feet (1.5 m) • at least 6 feet (1.8 m) from the gate/door or ANY moving part of the gate/door 11. This operator is intended for vehicular use ONLY. To prevent INJURY to pedestrians, a separate pedestrian access should be supplied, visible from the gate/door. Locate the pedestrian access where there is NOT a chance of INJURY at ANY point during full movement of the gate/door. 12. Install Warning signs on EACH side of gate/door in PLAIN VIEW. Install one Warning Sign next to the control station. Permanently secure each Warning sign in a suitable manner using fastening holes. 13. SAVE THESE INSTRUCTIONS. • ALWAYS wear protective gloves and eye protection when changing the battery or working around the battery compartment. • NEVER wear watches, rings or loose clothing while installing or servicing operator. They could be caught in gate/door or operator mechanisms. 9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
9
INSTALLATION
•
ALWAYS wear protective gloves and eye protection when changing the battery or working around the battery compartment.
•
NEVER wear watches, rings or loose clothing while installing or servicing operator. They could be caught in gate/door or operator mechanisms.
TO REDUCE THE RISK OF SEVERE INJURY OR DEATH:
IMPORTANT INSTALLATION INSTRUCTIONS
1.
READ AND FOLLOW ALL INSTRUCTIONS.
2.
Install operator ONLY on properly balanced and lubricated gate/
door. An improperly balanced gate/door may NOT reverse when
required and could result in SEVERE INJURY or DEATH.
3.
ALL repairs to cables, spring assemblies and other hardware MUST
be made by a trained systems technician BEFORE installing
operator.
4.
Disable ALL locks and remove ALL ropes connected to gate/door
BEFORE installing operator to avoid entanglement.
5. Install gate/door operator 8 feet (2.4 m) or more above floor.
6.
NEVER connect operator to power source until instructed to do so.
7.
Any openings shall be designed, guarded or screened to prevent a
2 1/4" (5.7 cm) diameter sphere from passing through the openings
anywhere in the gate/door.
8.
Entrapment protection devices MUST be installed to protect anyone
who may come near a moving gate/door. Upon completion of
installation, test entrapment protection device.
9.
Too much force on gate/door will interfere with proper operation of
safety reversal system.
•
NEVER increase force beyond minimum amount required to move
gate/door.
•
NEVER use force adjustments to compensate for a binding or
sticking gate/door.
•
If one control (force or travel limits) is adjusted, the other control
may also need adjustment.
10. Install control station:
• within sight of the gate/door
•
out of reach of children at minimum height of 5 feet (1.5 m)
•
at least 6 feet (1.8 m) from the gate/door or ANY moving part of
the gate/door
11.
This operator is intended for vehicular use ONLY. To prevent
INJURY to pedestrians, a separate pedestrian access should be
supplied, visible from the gate/door. Locate the pedestrian access
where there is NOT a chance of INJURY at ANY point during full
movement of the gate/door.
12.
Install Warning signs on EACH side of gate/door in PLAIN VIEW.
Install one Warning Sign next to the control station. Permanently
secure each Warning sign in a suitable manner using fastening
holes.
13.
SAVE THESE INSTRUCTIONS.