Magnavox 19MD359B User Manual - Page 19

Still Mode, Switching Each Input Mode, Switching Audio Mode

Page 19 highlights

INTRODUCTION PREPARATION WATCHING TV OPTIONAL SETTING OPERATING DVD DVD SETTING TROUBLESHOOTING INFORMATION 5 Still Mode You can pause the image shown on the TV screen. Press [FREEZE] to pause the image shown on the TV screen. FREEZE • The sound output will not be paused. • If no signal is detected or protected signal is received during still mode, the image remains paused and the sound output will be muted. • The still function will be released after 5 minutes. To cancel still mode, press any button except [y (power)]. 5 Switching Each Input Mode You can easily switch with the remote control to the DTV (ATSC) and TV (NTSC) or to access external devices when they are connected to the unit. Press [SOURCE] or [CH +] repeatedly to cycle through the input modes. 5 Switching Audio Mode This section describes how to switch the audio in the analog mode and how to switch the audio language in the digital mode. TV Press [SAP/AUDIO] to display the currently selected audio mode. While receiving an MTS broadcast, press repeatedly to cycle through the available audio channel. 11 SAP / STEREO When all audio are available SAP / STEREO SAP / MONO SAP / STEREO When stereo and monaural audio are available MONO / STEREO MONO / STEREO When SAP and monaural audio are available SAP / MONO SAP / MONO When only monaural audio is available STEREO SAP MONO MONO (cannot be switched) : Outputs stereo-audio : Outputs second audio program : Outputs mono-audio DTV/TV channel Video Component HDMI1 HDMI2 PC DTV 1 Press [SAP/AUDIO] to display the currently selected language and the number of available languages. 11.1 English 1/3 2 Press [SAP/AUDIO] repeatedly to cycle through the available audio languages. • Pressing [CH ] reverses the direction of the input modes. • Available languages differ depending on the broadcast. "Other" is displayed when the audio language cannot be acquired, or the acquired languages are other than English, Spanish or French. Note: • [SAP/AUDIO] does not control external audio devices. • The information display will automatically disappear in a few seconds. 19 EN

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56

19
EN
INTRODUCTION
PREPARATION
WATCHING TV
OPTIONAL SETTING
OPERATING DVD
DVD SETTING
TROUBLESHOOTING
INFORMATION
Still Mode
You can pause the image shown on the TV screen.
Press
[FREEZE]
to pause the image shown on the TV
screen.
FREEZE
The sound output will not be paused.
If no signal is detected or protected signal is received
during still mode, the image remains paused and the
sound output will be muted.
The still function will be released after 5 minutes.
To cancel still mode, press any button except
[
y
y
(power)
]
.
Switching Each Input Mode
You can easily switch with the remote control to the DTV (ATSC) and TV
(NTSC) or to access external devices when they are connected to the unit.
Press
[SOURCE]
or
[CH
+
]
repeatedly to cycle through
the input modes.
PC
Video
Component
HDMI1
HDMI2
DTV/TV channel
Pressing
[CH
]
reverses the direction of the input
modes.
Switching Audio Mode
This section describes how to switch the audio in the analog mode and how
to switch the audio language in the digital mode.
TV
Press
[SAP/AUDIO]
to display the currently selected
audio mode. While receiving an MTS broadcast,
press repeatedly to cycle through the available audio
channel.
11
SAP
/ STEREO
When all audio are available
SAP
/ STEREO
SAP
/ MONO
SAP /
STEREO
When stereo and monaural audio are available
MONO
/ STEREO
MONO /
STEREO
When SAP and monaural audio are available
SAP /
MONO
SAP
/ MONO
When only monaural audio is available
MONO
STEREO
: Outputs stereo-audio
SAP
: Outputs second audio program
MONO
: Outputs mono-audio
DTV
1
Press
[SAP/AUDIO]
to display the currently selected
language and the number of available languages.
11.1
English 1/3
2
Press
[SAP/AUDIO]
repeatedly to cycle through the
available audio languages.
Available languages differ depending on the
broadcast. “Other” is displayed when the audio
language cannot be acquired, or the acquired
languages are other than English, Spanish or French.
Note:
[SAP/AUDIO]
does not control external audio devices.
• The information display will automatically disappear in a
few seconds.
(cannot be switched)