Marantz AV9000 AV9000 USER'S MANUAL - Page 12
Remote Control Unit Rc-18sr - control center
View all Marantz AV9000 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 12 highlights
ENGLISH @0 96 kHz decode indicator This indicator is for 96 kHz PCM digital input signal. If the selected digital input signal is 96 kHz PCM audio, this indicator will illuminate. @1 DTS CINEMA and MUSIC indicator These indicators display the currently selected DTS mode. If you select DTS cinema or DTS music by SURROUND MODE SELECTOR buttons u, these indicators will display. @2 ENCODED CHANNEL STATUS indicator These indicators show which channels are encoded with a digital input signal. If the selected digital input signal is Dolby Digital 5.1ch or DTS 5.1ch, "L", "C", "R", "LS", "RS" and "LFE" will light up. If the digital input signal is 2 channel PCM-audio, "L" and "R" will be displayed. Note: These indicators are depend on the digital input, without reference to the surround mode. @3 PEAK indicator This indicator is a monitor for analog audio input signal. If the selected analog audio input signal is greater than the capable level of internal processing, this indicator will show. If this indicator is lit up, you should press the ATT button on the remote control. REMOTE CONTROL UNIT RC-18SR This chapter describes the functions which need to control the AV9000. See page 27 and following pages to refer other function of the RC-18SR. v POWER ON and OFF These two buttons are use for turning on or off AV9000. m DIRECT button The DIRECT command buttons (4 on each side of the LCD display, 8 total) work with the PAGE buttons (4 pages for each source component) to provide up to 32 dedicated specialized functions for each of the 11 function input selectors. Each DIRECT function may also be provided with an alphanumeric function indicator visible in the LCD display. Press the AMP or TUNER button . to control the receiver. Press one of these buttons to select a surround mode for the current listening session. AMP MODE1 MODE2 MODE3 1 AUTO 2 DOLB 3 THX 4 DTS 5 HALL 6 MTRX 7 MOV 8 2-CH 1 A/D 2 DIR 3 ATT 4 OSD 5 MONO 6 3-D 7 NITE 8 MLTI 1 TRB+ 2 TRB3 BAS+ 4 BAS5 R-EQ 6 CH+ Auto select surround modes Dolby Digital or Pro Logic decoding THX cinema decoding DTS-cinema or DTS-music Hall surround sound Matrix surround sound Movie surround sound Stereo sound (no surround) analog / digital select switch Switches between the analog input and the digital input. source direct switch When this switch is pressed, the signals are transmitted by bypassing the tone control circuitry so that they can be reproduced with higher quality. attenuate for analog input on screen display Once the button is pressed, the on-screen display is turned on and each a control button related to the AV9000 is pressed thereafter, the information will be displayed on the TV screen. When the button is pressed again to turn the on-screen display off, it disappears from the TV screen. (Refer to "ON-SCREEN MENU SYSTEM" on page 10) monaural decoding When this button is pressed, the monaural sound is selected. 3-D surround decoding This button is not used for AV9000. NIGHT mode for Dolby Digital Pressing this button prevents the Dolby Digital signal from playback at a loud voice. This function reduces the voice by 1/3 to 1/4 at maximum. Thus, it eliminates the occurrence of an abruptly loud voice at night. However, the function is valid only for the case when the Dolby Digital signal (AC-3) is entered into digital Input and data to compress the voice exists in the signal to be played back. activates multi-room mode increases treble decreases treble increases bass decreases bass The button 1 to 4 are used to control the tone. activates RE-EQ function This button is not used for AV9000. channel select button Press this button to adjust the volume levels of the front, center, surround, subwoofer channels. Each press of the button changes the channel which can be adjusted. 7