Marantz SR4300 User Guide - Page 38

ENGLISH 3. Each time the tuner finds a station, scanning will pause and the station will be played for five seconds. During this time, the following operations are possible. • The band can be changed by TUNER button . 4. If no button is pressed during this period, the current station is memorized in location Preset 02 If you wish to skip the current station, press the TUNING button during this period, this station is skipped and auto presetting continues. 5. Operation stops automatically when all 30 preset memory positions are filled or when auto scanning attains the highest endof all bands. If you desire to stop the auto preset memory at anytime, press the CLEAR button. MANUAL PRESET MEMORY 2. 4. 3. AV SURROUND RECEIVER SR4300 SURROUND 2. STANDBY POWER ON/STANDBY PHONES CLEAR MEMORY TUNING/PRESET F/P MODE A/D HT-EQ S-DIRECT DIMMER 6.1CH-IN TV DVD VCR1 DSS/VCR2 CDR/MD TAPE CD 3. POWER MEMO CLEAR SLEEP TREBLE BASS AUTO 1 2 DTS 3 CS 4 EX/ES 5 DSP 6 M-CH ST 7 2CH 8 6.1CH -IN 9 F.DIRECT A/D 0 OFF (Using the SR4300) 1. Tune into the radio station you desire (Refer to the "MANUAL TUNING" or "AUTO TUNING" section). 2. Press the MEMORY button on the front panel. "- -" (preset number) starts blinking on the display. 3. Select the preset number by pressing the TUNING or button, while this is still blinking (approx. 5 seconds) 4. Press the MEMORY button again to enter. The display stops blinking. The station is now stored in the specified preset memory location. (Using the remote control unit) 1. Tune into the radio station you desire (Refer to the "MANUAL TUNING" or "AUTO TUNING" section). 2. Press the MEMO button on the remote unite. "- -" (preset number)starts blinking on the display. 3. Enter the desired preset number by pressping numeric buttons. Note: • When entering a single digit number (2 for example), either input "02" or just input "2" and wait for a few seconds. RECALLING A PRESET STATION 2. 1. CLEAR MEMORY HT-EQ TUNING/PRESET S-DIRECT F/P DIMMER MODE 1. MUT TV DVD VCR1 DSS/VCR2 CDR/MD TAPE CD POWER MEMO CLEAR SLEEP TREBLE BASS AUTO 1 2 DTS 3 CS 4 EX/ES 5 DSP 6 M-CH ST 7 2CH 8 6.1CH -IN 9 F.DIRECT A/D 0 OFF 1. SETUP/T.TONE MENU S-DIRECT OK MUTE NIGHT VOLUME CHANNEL/SKIP TV CDR DVD MD TUNE/SEARCH MODE PTY (Using the SR4300) 1. Press the F/P button to show the preset station on the display. 2. Select the desired preset station by pressing the TUNING or button on the front panel (Using the remote control unit) 1. Press the 4 or ¢ button to select the desired preset station, or input your desired preset channel with numeric buttons on the remote. PRESET SCAN 1. 3. TV DVD VCR1 VCR2 DSS CDR MD TAPE CD TUNE/SEARCH MODE PTY DISP./RDS P.SCAN TUNER AMP ATT. SYSTEM REMOTE CONTROLLER RC4300SR 3. POWER MEMO CLEAR SLEEP TREBLE AUTO 1 CS 4 M-CH ST 7 2 EX/ES 5 2CH 8 DTS 3 DSP 6 6.1CH -IN 9 (Using the remote control unit) 1. Press the P.SCAN on remote. "PRESET SCAN" appears on the display and then the preset station with the lowest preset number is recalled first. 2. Preset stations are recalled in sequence (No.1 → No.2 → etc.) for 5 seconds each. No stored preset number will be skipped. 3. You can fast forward the preset stations by pressping the § continuously. When the desired preset station is received, cancel the preset scan operation by pressping the CLEAR or P.SCAN. CLEARING STORED PRESET STATIONS You can remove preset stations from memory using the following procedure. 3. 2. AV SURROUND RECEIVER SR4300 SURROUND STANDBY POWER ON/STANDBY PHONES CLEAR MEMORY TUNING/PRESET F/P MODE A/D HT-EQ S-DIRECT DIMMER 6.1CH-IN TV DVD VCR1 DSS/VCR2 CDR/MD TAPE CD 2. 3. POWER MEMO CLEAR SLEEP TREBLE BASS AUTO 1 2 DTS 3 CS 4 EX/ES 5 DSP 6 M-CH ST 7 2CH 8 6.1CH -IN 9 F.DIRECT A/D 0 OFF 1. Recall the preset number to be cleared with the method described in "RECALLING" a preset station. 2. Press the MEMORY button on the front panel or press MEMO button on the remote. 3. Stored preset number blinks in the display for 5 seconds. While blinking, press the CLEAR button on the front panel or press CLEAR on the remote unit. 4. "xx CLEAR" appears on the display to indicate that the specified preset number has been cleared. Notes: • To clear stored all preset stations, press and hold the CLEAR and the F/P buttons for two seconds. 34