NEC NP-UM330X User's Manual - Page 15

Removing and Attaching the Cable Cover, Introduction

Get NEC NP-UM330X PDF manuals and user guides View all NEC NP-UM330X manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

Removing and Attaching the Cable Cover After finishing connections, attach the supplied cable cover to properly hide the cables. 1. Introduction CAUTION: • Be sure to tighten the screws after attaching the cable cover. Failure to do so may cause the cable cover to come off and fall, resulting in injury or damage to the cable cover. • Do not put bundled cables in the cable cover. Doing so may damage the power cord, resulting in a fire. • Do not hold the cable cover while moving the projector or do not apply excessive force to the cable cover. Doing so may damage the cable cover, resulting in injury. Removing the cable cover Tool needed: • Phillips screwdriver (plus-head) about 9 cm/4 inches in length 9 cm/4 inches 1. Loosen the cable cover screws until the Phillips screwdriver goes into a freewheeling condition 2. Remove the cable cover.  Push up the cable cover slightly and rotate it to release. 2  Pull the cable cover while pushing and holding the arrow part If you find it to hard to release the cable cover, try holding it slightly up. 1 5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
5
1. Introduction
Removing and Attaching the Cable Cover
After finishing connections, attach the supplied cable cover to properly hide the cables.
CAUTION:
• Be sure to tighten the screws after attaching the cable cover.Failure to do so may cause the cable cover to come
off and fall, resulting in injury or damage to the cable cover.
• Do not put bundled cables in the cable cover.Doing so may damage the power cord, resulting in a fire.
• Do not hold the cable cover while moving the projector or do not apply excessive force to the cable cover.Doing so
may damage the cable cover, resulting in injury.
Removing the cable cover
Tool needed:
• Phillips screwdriver (plus-head) about 9 cm/4 inches in length
9 cm/4 inches
1. Loosen the cable cover screws until the Phillips screw-
driver goes into a freewheeling condition
2. Remove the cable cover.
1
Push up the cable cover slightly and rotate it to release.
Pull the cable cover while pushing and holding the arrow
part
If you find it to hard to release the cable cover, try holding it
slightly up.
1
2