Netgear GA622T GA622T Reference Manual - Page 45

In the Board GA622_1 Driver GA622 Actions dialog box, click Select/Modify

Get Netgear GA622T - Copper Gigabit Ethernet Card PDF manuals and user guides
UPC - 606449021561
View all Netgear GA622T manuals
Add to My Manuals
Save this manual to your list of manuals

Page 45 highlights

Modifying Driver Properties Note: The driver properties can be modified only during the driver software installation. If you want to modify these properties after the driver has already installed, you must first remove the driver, and then reinstall it. 1. Repeat steps 1-9 from the above procedure. 2. In the Board GA622_1 (Driver GA622) Actions dialog box, click Select/Modify driver parameters and protocols. 3. Use the Tab and Arrow keys to move the cursor to GA622T_1 Parameters dialog box, where you can change driver parameters. Refer to Table 6-3 for help in configuring these parameters. Table 6-3. Parameter Descriptions Parameter Descriptions Slot Number Supported values: any decimal number with a maximum length of 8 figures. Select the slot number that corresponds to the expansion slot where the board is installed. Caution: If this parameter is not correctly supplied and there is more than one card installed in the server, the installation program may crash the system. Node Address Supported values: any hexadecimal number (digits 0 to F allowed) with a maximum length of 12 figures. DO NOT change this address unless you are prepared to administer local addresses according to IEEE 802.2 specifications.The driver defaults to the node address on the board (whether factory-set or manually set). Receive Buffer Count Supported values: 50-150. Default value: 150 This is the number of receive descriptors to use. Transmit Buffer Count Supported values: 50-150. Default value: 150 This is the number of transmit descriptors to use. NetWare driver software 6-5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
NetWare driver software
6-5
Modifying Driver Properties
Note:
The driver properties can be modified only during the driver software
installation. If you want to modify these properties after the driver has already
installed, you must first remove the driver, and then reinstall it.
1.
Repeat steps 1
–
9 from the above procedure.
2.
In the Board GA622_1 (Driver GA622) Actions dialog box, click Select/Modify
driver parameters and protocols.
3.
Use the Tab and Arrow keys to move the cursor to GA622T_1 Parameters dialog
box, where you can change driver parameters. Refer to Table 6-3 for help in con-
figuring these parameters.
Table 6-3.
Parameter Descriptions
Parameter
Descriptions
Slot Number
Supported values:any decimal number with a maximum length of 8 figures.
Select the slot number that corresponds to the expansion slot where the board
is installed.
Caution:
If this parameter is not correctly supplied and there is more than one
card installed in the server,the installation program may crash the system.
Node Address
Supported values:any hexadecimal number (digits 0 to F allowed) with a
maximum length of 12 figures.
DO NOT change this address unless you are prepared to administer local
addresses according to IEEE 802.2 specifications.The driver defaults to the
node address on the board (whether factory-set or manually set).
Receive Buffer Count
Supported values: 50
–
150. Default value: 150
This is the number of receive descriptors to use.
Transmit Buffer Count
Supported values: 50
–
150. Default value: 150
This is the number of transmit descriptors to use.