Netgear WG302 WG302v1 Reference Manual - Page 58

Con the WG302 AP3 in Repeater mode with the Remote MAC Address of AP2.

Get Netgear WG302 - 802.11g ProSafe Wireless Access Point PDF manuals and user guides
UPC - 606449030365
View all Netgear WG302 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 58 highlights

Reference Manual for the WG302 802.11g ProSafe Wireless Access Point - Configure the WG302 (AP3) in Repeater mode with the Remote MAC Address of AP2. 2. Verify the following parameters for all access points: • Verify that the LAN network configuration the WG302 Access Points are configured to operate in the same LAN network address range as the LAN devices • All APs must be on the same LAN. That is, all the APs LAN IP address must be in the same network. • If using DHCP, all WG302 Access Points should be set to "Obtain an IP address automatically (DHCP Client)" in the IP Address Source portion of the Basic IP Settings menu. • All WG302 Access Points use the same SSID, Channel, authentication mode, if any, and encryption in use. 3. Verify connectivity across the LANs. • A PC on any LAN segment should be able to connect to the Internet or share files and printers with any other PCs or servers connected to any of the three WLAN segments. Note: You can extend this repeating by adding up to 2 additional WG302s configured in repeater mode. However, since Repeater configurations communicate in half-duplex mode, the bandwidth decreases as you add Repeaters to the network. Also, you can extend the range of the wireless network with NETGEAR wireless antenna accessories. 5-6 Advanced Configuration December 2003

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
Reference Manual for the WG302 802.11g ProSafe Wireless Access Point
5-6
Advanced Configuration
December 2003
–
Configure the WG302 (AP3) in Repeater mode with the Remote MAC Address of AP2.
2.
Verify the following parameters for all access points:
•
Verify that the LAN network configuration the WG302 Access Points are configured to
operate in the same LAN network address range as the LAN devices
•
All APs must be on the same LAN. That is, all the APs LAN IP address must be in the
same network.
•
If using DHCP, all WG302 Access Points should be set to “Obtain an IP address
automatically (DHCP Client)” in the IP Address Source portion of the Basic IP Settings
menu.
•
All WG302 Access Points use the same SSID, Channel, authentication mode, if any, and
encryption in use.
3.
Verify connectivity across the LANs.
•
A PC on any LAN segment should be able to connect to the Internet or share files and
printers with any other PCs or servers connected to any of the three WLAN segments.
Note:
You can extend this repeating by adding up to 2 additional WG302s configured in repeater
mode. However, since Repeater configurations communicate in half-duplex mode, the bandwidth
decreases as you add Repeaters to the network. Also, you can extend the range of the wireless
network with NETGEAR wireless antenna accessories.