NordicTrack Cxt 970 User Manual - Page 7

on the Left Spring Arm. Slide the Right Upper Body - elliptical crosstrainer

Get NordicTrack Cxt 970 PDF manuals and user guides View all NordicTrack Cxt 970 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 7 highlights

6. Identify the Left Pedal (41). Attach the Left Pedal to the Left Spring Arm (3) with an M10 x 36mm Carriage 6 Bolt (61), an M10 Washer (63), and an Adjustment Knob (77) as shown. Note: The Left Pedal can be attached in any of five positions (see HOW TO ADJUST THE PEDALS on page 9). Attach the Right Pedal (not shown) in the same way. Make sure that both Pedals are in the same position. 61 41 3 63 77 7. Apply a small amount of the included Teflon® lubricant to a paper towel. Rub a thin film of the lubricant onto the Chrome Tubes (21) on the Left and Right Spring Arms (3, 4). Next, slide the Left Upper Body Arm (7), which is marked with a sticker, onto the Chrome Tube on the Left Spring Arm. Slide the Right Upper Body Arm (75) onto the Chrome Tube on the Right Spring Arm. Make sure that the Upper Body Arms are on the correct sides-the upper ends should bend in the direction shown by the arrows. Next, slide an Axle Cover (74) onto the post on each Upper Body Arm. Apply grease to the Arm Axle (19). Insert the Arm Axle into the right Axle Cover (74) and the Right Upper Body Arm (75). Next, insert the Arm Axle into the Upright (2) until the left end of the Arm Axle is flush with the left side of the Upright. Then, insert the Arm Axle into the left Axle Cover (74) and the Left Upper Body Arm (7). Center the Arm Axle (19). Using the included pedal tool, tap two Push Nuts (15) about 1/8" onto each end of the Arm Axle. Make sure that the Push Nuts are turned as shown in the inset drawing. (Note: It may be helpful if another person holds a block of wood against one end of the Arm Axle while you tap Push Nuts onto the other end.) Then, press an Axle Cap (34) onto each end of the Arm Axle. 8. Plug the Power Supply (13) into the jack at the rear of the elliptical crosstrainer. Note: Your Power Supply may look different from the one pictured. 7 75 74 19 74 7 34 15 Grease Post 34 15 2 21 4 21 3 Pedal Tool 15 19 8 Jack 13 9. Make sure that all parts of the elliptical crosstrainer are properly tightened. Note: Some hardware may be left over after assembly is completed. 7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
7
6.
Identify the Left Pedal (41). Attach the Left Pedal to
the Left Spring Arm (3) with an M10 x 36mm Carriage
Bolt (61), an M10 Washer (63), and an Adjustment
Knob (77) as shown. Note: The Left Pedal can be
attached in any of five positions (see HOW TO
ADJUST THE PEDALS on page 9).
Attach the Right Pedal (not shown) in the same way.
Make sure that both Pedals are in the same position.
6
61
41
77
63
3
7.
Apply a small amount of the included Teflon
®
lubricant
to a paper towel. Rub a thin film of the lubricant onto
the Chrome Tubes (21) on the Left and Right Spring
Arms (3, 4). Next, slide the Left Upper Body Arm (7),
which is marked with a sticker, onto the Chrome Tube
on the Left Spring Arm. Slide the Right Upper Body
Arm (75) onto the Chrome Tube on the Right Spring
Arm.
Make sure that the Upper Body Arms are on
the correct sides—the upper ends should bend in
the direction shown by the arrows.
Next, slide an
Axle Cover (74) onto the post on each Upper Body Arm.
Apply grease to the Arm Axle (19). Insert the Arm Axle
into the right Axle Cover (74) and the Right Upper Body
Arm (75). Next, insert the Arm Axle into the Upright (2)
until the left end of the Arm Axle is flush with the left
side of the Upright. Then, insert the Arm Axle into the
left Axle Cover (74) and the Left Upper Body Arm (7).
Center the Arm Axle (19). Using the included pedal
tool, tap two Push Nuts (15)
about 1/8”
onto each end
of the Arm Axle. Make sure that the Push Nuts are
turned as shown in the inset drawing. (Note: It may be
helpful if another person holds a block of wood against
one end of the Arm Axle while you tap Push Nuts onto
the other end.) Then, press an Axle Cap (34) onto each
end of the Arm Axle.
7
21
21
2
74
Post
Grease
74
19
34
34
15
15
7
4
75
Pedal Tool
15
19
3
8.
Plug the Power Supply (13) into the jack at the rear of
the elliptical crosstrainer.
Note: Your Power Supply
may look different from the one pictured.
8
13
Jack
9.
Make sure that all parts of the elliptical crosstrainer
are properly tightened.
Note: Some hardware may be
left over after assembly is completed.