NordicTrack Elite 3750 Treadmill User Manual - Page 13

If You Do Not Connect

Get NordicTrack Elite 3750 Treadmill PDF manuals and user guides View all NordicTrack Elite 3750 Treadmill manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

10. IMPORTANT: To avoid damaging the Pulse Crossbar (80), do not use power tools, and do 10 2 6 not overtighten the #10 x 3/4" Screws (6) or the 5/16" x 2" Screws (2). 8 Orient the Pulse Crossbar (80) as shown. Attach the Pulse Crossbar with two of the 5/16" x 2" Screws (2) that you removed in step 5, two 5/16" 2 Star Washers (8), and two #10 x 3/4" Screws (6); start all four Screws, and then tighten them. Then, tighten the other two 5/16" x 2" Screws (2). 80 2 6 8 2 11. With the help of a second person, hold the con- 11 sole assembly (H) near the Handrails (74). See the inset drawing. Connect the Upright Wire (83) to the console wire (J). The connec- tors should slide together easily and snap into place. If they do not, turn one connector and try again. IF YOU DO NOT CONNECT THE CONNECTORS PROPERLY, THE CONSOLE MAY BECOME DAMAGED WHEN YOU TURN ON THE POWER. H Then, remove any wire tie from the Upright Wire (83) and insert the Wire into the Right Upright (84). J 83 74 84 J 83 13

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
13
11.
With the help of a second person, hold the con-
sole assembly (H) near the Handrails (74).
See the inset drawing.
Connect the Upright
Wire (83) to the console wire (J).
The connec-
tors should slide together easily and snap
into place.
If they do not, turn one connector
and try again.
IF YOU DO NOT CONNECT THE
CONNECTORS PROPERLY, THE CONSOLE
MAY BECOME DAMAGED WHEN YOU TURN
ON THE POWER.
Then, remove any wire tie from the Upright Wire
(83) and insert the Wire into the Right Upright
(84).
83
84
H
J
11
10.
IMPORTANT: To avoid damaging the Pulse
Crossbar (80), do not use power tools, and do
not overtighten the #10 x 3/4" Screws (6) or
the 5/16" x 2" Screws (2).
Orient the Pulse Crossbar (80) as shown. Attach
the Pulse Crossbar with two of the 5/16" x 2"
Screws (2) that you removed in step 5, two 5/16"
Star Washers (8), and two #10 x 3/4" Screws (6);
start all four Screws, and then tighten them.
Then, tighten the other two 5/16" x 2"
Screws (2).
80
10
8
8
2
2
83
J
2
2
6
6
74