Onkyo HT-S9800THX Basic/Advanced Manual - English - Page 38

>>Specifications >>Advanced Setup >>Listening Modes >>Network Functions >>Basic Manual Troubleshooting | Supplementary Information, etc. ˙ 3� Level Calibration Setting Item Front Left Center Front Right Height Left Height Right Surround Right Default Value 0 dB 0 dB 0 dB 0 dB 0 dB 0 dB Setting Details Select a value between "ʵ12 dB" and "ʴ12 dB" (in 1 dB increments). A test tone will be output each time you change the value. Select the desired level. Select a value between "ʵ12 dB" and "ʴ12 dB" (in 1 dB increments). A test tone will be output each time you change the value. Select the desired level. Select a value between "ʵ12 dB" and "ʴ12 dB" (in 1 dB increments). A test tone will be output each time you change the value. Select the desired level. Select a value between "ʵ12 dB" and "ʴ12 dB" (in 1 dB increments). A test tone will be output each time you change the value. Select the desired level. • The setting cannot be changed if "Zone 2" is set in "Configuration" - "Zone Speaker" and Zone 2 is on. Select a value between "ʵ12 dB" and "ʴ12 dB" (in 1 dB increments). A test tone will be output each time you change the value. Select the desired level. • The setting cannot be changed if "Zone 2" is set in "Configuration" - "Zone Speaker" and Zone 2 is on. Select a value between "ʵ12 dB" and "ʴ12 dB" (in 1 dB increments). A test tone will be output each time you change the value. Select the desired level. Setting Item Surr Back Right Surr Back Left Surround Left Subwoofer Default Value 0 dB 0 dB 0 dB 0 dB Setting Details Select a value between "ʵ12 dB" and "ʴ12 dB" (in 1 dB increments). A test tone will be output each time you change the value. Select the desired level. • The setting cannot be changed if "Zone 2" is set in "Configuration" - "Zone Speaker" and Zone 2 is on. Select a value between "ʵ12 dB" and "ʴ12 dB" (in 1 dB increments). A test tone will be output each time you change the value. Select the desired level. • The setting cannot be changed if "Zone 2" is set in "Configuration" - "Zone Speaker" and Zone 2 is on. Select a value between "ʵ12 dB" and "ʴ12 dB" (in 1 dB increments). A test tone will be output each time you change the value. Select the desired level. Select a value between "ʵ15 dB" and "ʴ12 dB" (in 1 dB increments). A test tone will be output each time you change the value. Select the desired level. ˙ 4� Dolby Enabled Speaker Setting Item Dolby Enabled Speaker to Ceiling AccuReflex Default Value 6.0 ft/1.80 m Off Setting Details Set the distance between the Dolby Enabled Speaker and the ceiling. Select between "0.1 ft/0.03 m" to "15.0 ft/4.50 m" (0.1 ft/0.03 m units). • The unit of distance (ft/m) shown is the unit selected for use in "Distance". You can enhance the reflection effect of Dolby Enabled Speakers from the ceiling. "Off": When this function is not to be used "On": When this function is to be used • This setting can be selected when "Configuration" - "Height Speaker" is set to "Dolby Speaker". 13