Optoma EH504 User manual

Optoma EH504 Manual

Get Optoma EH504 PDF manuals and user guides View all Optoma EH504 manuals
Add to My Manuals
Save this manual to your list of manuals

Optoma EH504 manual content summary:

  • Optoma EH504 | User manual - Page 1
    DLP® Projector User manual
  • Optoma EH504 | User manual - Page 2
    Contents SAFETY 4 Important Safety Instruction...4 3D Safety Information...5 projector...14 Connecting sources to the projector (1080P / WXGA 15 Connecting sources to the projector (XGA 16 Adjusting the projector image...17 Remote setup...18 USING THE PROJECTOR 20 Powering on / off the projector
  • Optoma EH504 | User manual - Page 3
    menu...57 Options menu...58 Options lamp settings menu...59 Options remote settings Projector dimensions and ceiling mount installation 74 RS232 protocol function list...75 IR remote codes...83 Using the Information button...85 Troubleshooting...86 Warning indicators...87 Specifications...89 Optoma
  • Optoma EH504 | User manual - Page 4
    maintenance (servicing) instructions in the literature accompanying the appliance. Please follow all warnings, precautions and maintenance as recommended in this user's guide. Important Safety Instruction ‡‡ Do not block any ventilation openings. To ensure reliable operation of the projector and to
  • Optoma EH504 | User manual - Page 5
    by appropriate service personnel. ‡‡ Only use attachments/accessories specified by the manufacturer. ‡‡ Do not look into straight into the projector lens during operation. The bright light may harm your eyes. ‡‡ When replacing the lamp, please allow the unit to cool down. Follow instructions as
  • Optoma EH504 | User manual - Page 6
    It is recommended that users take frequent breaks to Accordingly, DO NOT place your 3D PROJECTOR near open stairwells, cables, balconies, DLP logo are registered trademarks of Texas Instruments and BrilliantColorTM is a trademark of Texas Instruments. All other product names used in this manual
  • Optoma EH504 | User manual - Page 7
    could void the user's authority, which is granted by the Federal Communications Commission, to operate this projector. Operation Conditions This & TTE Directive 1999/5/EC (if product has RF function) WEEE Disposal instructions Do not throw this electronic device into the trash when discarding. To
  • Optoma EH504 | User manual - Page 8
    Standard accessories Projector Power Switch Freeze L R Enter Page- Laser Page+ Keystone -+ Volume -+ 1 4 HDMI 7 User1 Source 2 Menu 5 VGA 8 User2 0 3 3D 6 Video 9 User3 Resync Remote Control 2x AAA batteries Power cord  CD User Manual  Warranty Card*  Basic User Manual VGA cable
  • Optoma EH504 | User manual - Page 9
    6 4 7 9 8 13 12 11 10 Note: Do not block projector inlet or outlet air vents. No Item 1. Lens 2. Focus Ring 3. Lens Shift (vertical) 4. IR Receiver 5. Keypad 6. Ventilation (inlet) 7. Zoom Lever No Item 8. Lamp Cover 9. Ventilation (outlet) 10. Tilt-Adjustment Foot 11. Input
  • Optoma EH504 | User manual - Page 10
    9 10 11 16 15 14 Note: Remote mouse requires special remote. No Item 1. HDMI3 / MHL connector 2. RJ-45 connector 3. MOUSE / SERVICE connector 4. HDMI1 connector 5. HDMI2 / MHL connector 6. VGA-In / YPbPr connector 7. VGA-Out connector 8. Video connector 13 12 No Item 9. Audio2
  • Optoma EH504 | User manual - Page 11
    12 13 21 20 19 Note: Remote mouse requires special remote. No Item 1. HDMI3 / MHL connector 2. RJ-45 connector 3. MOUSE / SERVICE connector 4. HDMI1 connector 5. HDMI2 / MHL connector 6. VGA1-In / YPbPr connector 7. VGA-Out connector 8. S-Video connector 9. MIC connector 10. Audio2
  • Optoma EH504 | User manual - Page 12
    INTRODUCTION Keypad 1 23 4 12 5 11 6 10 7 9 8 3 No Item 1. On / Standby LED 2. Lamp LED 3. Keystone Correction (vertical) 4. Temp LED 5. IR Receiver 6. Re-Sync No Item 7. Information 8. Enter 9. Four Directional Select Keys 10. Power 11. Source 12. Menu 12 English
  • Optoma EH504 | User manual - Page 13
    6. Laser 7. Page - 8. Keystone 9. Menu 10. Aspect Ratio 11. HDMI 12. User 2 13. User 1 14. Source No Item 15. Brightness Mode 16. Mouse On / Off 17. On / Off 23. VGA 24. Video 25. User 3 26. Resync 27. Numeric Keypad (0-9) Note: Some keys may have no function for models that do
  • Optoma EH504 | User manual - Page 14
    mount. The projector should be horizontal and not tilted either forwards/backwards or left/right. Any other orientation will invalidate the warranty and may shorten the lifetime of the projector lamp or the projector itself. For none standard installation advise please contact Optoma. 14 English
  • Optoma EH504 | User manual - Page 15
    SETUP AND INSTALLATION Connecting sources to the projector (1080P / WXGA) 3 12 15 13 14 4 5 6 87 12 11 10 9 Note: ‡‡ ‡‡ ‡‡ performing the connection to the HDMI3 / MHL connector. If not powered off manually, the projector will automatically power off as soon as the top cover is opened. Due
  • Optoma EH504 | User manual - Page 16
    SETUP AND INSTALLATION Connecting sources to the projector (XGA) 34 18 12 567 8 16 17 9 11 10 15 12 14 13 Note: prior performing the connection to the HDMI3 / MHL connector. If not powered off manually, the projector will automatically power off as soon as the top cover is opened. Due
  • Optoma EH504 | User manual - Page 17
    adjusting the image height. 1. Locate the adjustable foot you wish to adjust on the underside of the projector. 2. Rotate the adjustable foot clockwise or counter-clockwise to raise or lower the projector. Tilt-Adjustment Feet Tilt-Adjustment Ring Zoom and focus ‡‡ To adjust the image size, turn the
  • Optoma EH504 | User manual - Page 18
    result in chemical leakage or explosion. Be sure to follow the instructions below. ‡‡ Do not mix batteries of different types. Different types close to Inverter-Type fluorescent lamps, it might become ineffective from time to time. ‡‡ If the remote control and the projector are within a very short
  • Optoma EH504 | User manual - Page 19
    SETUP AND INSTALLATION Approx. ± 15° Approx. ± 15° English 19 3 3D 6 Video 9 User3 Resync 2 Menu 5 VGA 8 User2 0 1 4 HDMI 7 User1 Source Volume -+ Keystone -+ Page- Laser Page+ Enter R L Freeze Switch Power Power Switch Freeze L R Enter + Laser + - PageK-eystone -1 PVaogleu+me 3
  • Optoma EH504 | User manual - Page 20
    again 3. Press the " " again to confirm, otherwise the message will disappear after 15 seconds. When you press the " " button for the second time, the projector will shut down. 4. The cooling fans will continue to operate for about 10 seconds for the cooling cycle and the On/ Standby LED will flash
  • Optoma EH504 | User manual - Page 21
    + Keystone Volume Turn on the connected source that you want to display on the screen such a-s com+ put-er, no+tebook, video player, etc. The projector will automatically detect the source. If multiple sources are c1 onne2cted, 3push the source button on the
  • Optoma EH504 | User manual - Page 22
    to confirm, and the screen will return to the main menu. 6. To exit, press "Menu" again. The OSD menu will close and the projector will automatically save the new settings. Main Menu Sub Menu IMAGE Display Mode Brightness Contrast Sharpness Color Tint Advanced Presentation Settings 22 English
  • Optoma EH504 | User manual - Page 23
    USING THE PROJECTOR OSD Menu tree Main menu Sub menu Display Mode Brightness Contrast mode can adjust and save in each mode DICOM SIM. User 3D -50~50 -50~50 1 ~15 -50~50 -50~50 0~10 1~10 On Note: End-user can choose lamp mode between Bright and Eco while DynamicBlack is Off; Off
  • Optoma EH504 | User manual - Page 24
    USING THE PROJECTOR Main menu Sub menu Image Advanced Reset Display Format Zoom Edge Mask Image Shift Geometric Correction Advanced menu Color Matching Signal (RGB) Signal (Video) Exit H: 0; V: -
  • Optoma EH504 | User manual - Page 25
    USING THE PROJECTOR Main menu Sub menu Display Geometric Correction 3D Setup Language Advanced menu Auto V. Keystone Four Corner Reset 3D Mode 3D->2D 3D Format 3D Sync Invert Exit Single-item menu On Off Top-Left Top-Right Bottom-Left Bottom-Right Yes No DLP-Link VESA 3D Off 3D L R Auto SBS
  • Optoma EH504 | User manual - Page 26
    Main menu Sub menu Language Projection Screen Type Menu Location Setup Security Projector ID Audio Settings Advanced menu Security Security Timer Change Password Exit Internal Speaker Mute Volume Audio Input Single-item menu Vietnamese Romanian Indonesian Front Rear
  • Optoma EH504 | User manual - Page 27
    USING THE PROJECTOR Main menu Sub menu Audio Settings Setup Advanced Network - Considering power consumption in active mode, AudioOut(Standby) supports only analog audio input (HDMI audio is out from AudioInput1). - End-user can enable / disable AudioOut(Standby) while PowerMode(Standby)
  • Optoma EH504 | User manual - Page 28
    USING THE PROJECTOR Main menu Options Sub menu Input Source Source Lock High Altitude Information Hide Keypad Lock Display Mode Lock Test Pattern Background Color Wall Color Remote
  • Optoma EH504 | User manual - Page 29
    -user can enable / disable SignalPowerOn while PowerMode(Standby) is Active. - SignalPowerOn can support Lamp Hour Lamp Reminder Lamp Mode Lamp Reset Exit On Off Active Eco. On Off Bright Eco Dynamic Eco+ Yes No [Default Off] [Default Eco.] [Read-Only] [Default Off] Note: End-user can choose lamp
  • Optoma EH504 | User manual - Page 30
    , the phase, frequency items will appear for user to manually tune and saved in settings. The "LAMP RESET" in OSD will only reset both Lamp Hours in OSD and Lamp Hours in service mode. The Projection Hours in service mode will not be reset. If the end-user changes the Audio setting from "Default" to
  • Optoma EH504 | User manual - Page 31
    USING THE PROJECTOR Image menu IMAGE Display Mode Brightness Contrast Sharpness Color Tint Advanced Presentation Reset Exit Display Mode There are many factory presets optimized for various types of images. Display Mode Presentation Bright Movie sRGB Blackboard 3D DICOM SIM. User ‡‡ Presentation
  • Optoma EH504 | User manual - Page 32
    USING THE PROJECTOR Brightness Adjust the brightness of the image. ‡‡ Press the to darken image. ‡‡ Press the to lighten the image. Contrast The contrast controls the degree of
  • Optoma EH504 | User manual - Page 33
    in picture. ‡‡ Press the ‡‡ Press the Dynamic Black to stronger enhance the image. to less enhance the image. Dynamic Black enables the projector to automatically optimize the brightness of the display during dark / light movie scenes to be shown in incredible detail. Gamma This allows you to
  • Optoma EH504 | User manual - Page 34
    USING THE PROJECTOR Color Space Press the or to select an appropriate color matrix type from the following: ‡‡ Not-HDMI Input: Auto, RGB or YUV ‡‡ HDMI Input: Auto,
  • Optoma EH504 | User manual - Page 35
    the Phase, frequency items are grayed out. If this function is disabled, the phase, frequency items will appear for user to manually tune and saved in settings after the next time projector turns off and on again. Phase Synchronize the signal timing of the display with the graphic card. If the image
  • Optoma EH504 | User manual - Page 36
    USING THE PROJECTOR Image advanced signal (video) menu IMAGE Advanced : Signal White Level Black Level IRE Exit White Level Allow user to adjust White Level when inputting Video signals. Black Level Allow user to adjust Black Level when inputting Video signals. IRE Allow user to adjust IRE
  • Optoma EH504 | User manual - Page 37
    USING THE PROJECTOR Display menu Format DISPLAY Zoom Edge Mask Image Shift Geometric input sources, like widescreen laptops. ‡‡ LBX: This format is for non-16 x 9, letterbox source and for users who use external 16 x 9 lens to display 2.35:1 aspect ratio using full resolution. ‡‡ Native: This
  • Optoma EH504 | User manual - Page 38
    USING THE PROJECTOR WXGA: ‡‡ ‡‡ LBX: This format is for non-16x9, letterbox source and for users who use external 16x9 lens to display 2.35:1 aspect ratio using full that supports anamorphic wide is enhanced for 16x9 Display in a wide 2.35:1 image. In this case, there are no black bars. Lamp power
  • Optoma EH504 | User manual - Page 39
    USING THE PROJECTOR XGA: ‡‡ 4:3: This format is for 4:3 input sources. ‡‡ 16:9: This format is for 16:9 input sources, like widescreen laptops. ‡‡ Native: This format displays the original image
  • Optoma EH504 | User manual - Page 40
    USING THE PROJECTOR Display geometric correction menu DISPLAY Geometric Correction H. Keystone V. Keystone Auto V. Keystone Four Corner Reset Off Exit Geometric correction ‡‡ H. Keystone (Horizontal Keystone): Press the to correct
  • Optoma EH504 | User manual - Page 41
    THE PROJECTOR Display 3D menu DISPLAY 3D Mode Off 3D Format 3D Sync. Invert Auto Off Exit 3D Mode Use this function to disable the 3D function or select the appropriate the 3D function. 3D Mode Off DLP-Link VESA 3D ‡‡ Off: Select "Off" to turn off 3D mode. ‡‡ DLP-Link: Select "DLP-Link
  • Optoma EH504 | User manual - Page 42
    Setup menu SETUP Language Projection Screen Type Menu Location Security Projector ID Audio Settings English Advanced Network Exit Language Choose the multilingual OSD menu. Press into the sub menu and then use the , , or key to
  • Optoma EH504 | User manual - Page 43
    from 16:10 or 16:9 (WXGA). Note: "Screen Type" is for WXGA only. Menu Location Choose the menu location on the display screen. Projector ID ID definition can be set up by menu (range 0-99), and allow user control an individual projector by RS232. Exit Choose "Exit" to exit the menu. English 43
  • Optoma EH504 | User manual - Page 44
    mute off. Note: "Mute" function affects both internal and external speaker volume. Audio Input The default audio settings are on the back panel of the projector. Use this option to reassign any of the Audio Inputs (1 or 2) to the current image source. Each Audio input can be assigned to more than
  • Optoma EH504 | User manual - Page 45
    Security menu Security SETUP Security Security Timer Change Password Off Exit Security Enable this function to prompt for a password before using the projector. ‡‡ On: Choose "On" to use security verification when the turning on the projector. ‡‡ Off: Choose "Off" to be able to switch on the
  • Optoma EH504 | User manual - Page 46
    and press the "Enter" key to confirm. If the incorrect password is entered 3 times, the projector will automatically shut down. If you have forgotten your password, please contact your local office for support. Note: The password default value is "1234" (first time). Enter Current security Code
  • Optoma EH504 | User manual - Page 47
    Projector will obtain an IP address automatically from your network. ‡‡ Off: To assign IP, Subnet Mask, Gateway and DNS configuration manually. the projector's IP address ("Network: LAN Settings > IP Address"). 3. Enter the user name and password, and click "Login". The projector's configuration
  • Optoma EH504 | User manual - Page 48
    USING THE PROJECTOR Note: ‡‡ ‡‡ The default user name and password is "admin". The steps in this section is based on Windows 7 operating system. Making a direct connection from your computer to the projector* 1. Turn "Off" the DHCP option on the projector. 2. Configure the IP address, Subnet
  • Optoma EH504 | User manual - Page 49
    USING THE PROJECTOR Setup network control settings menu SETUP Network : Control Settings Crestron Off Extron Off PJ Link Off AMX Device Discovery Off Telnet Off HTTP Off Exit
  • Optoma EH504 | User manual - Page 50
    /english/ For more detailed information about the various types of external devices which can be connected to the LAN / RJ45 port and remote control the projector, as well as the supported commands for these external devices, please contact the Support-Service directly. 50 English
  • Optoma EH504 | User manual - Page 51
    LAN RJ45 1. Connect an RJ45 cable to RJ45 ports on the projector and the PC (laptop). 2. On the PC (Laptop), select Start > Control Panel > Network Connections. 3. Right-click on the Local Area Connection, and select Property. 4. In
  • Optoma EH504 | User manual - Page 52
    5. Click "Properties". 6. Type in the IP address and Subnet mask, then press "OK". 7. Press the "Menu" button on the projector. 8. Use the keys to select SETUP > Network > LAN Settings. 9. Enter the following connection parameters: ±± DHCP: Off ±± IP Address: 10.10.10.10 ±± Subnet Mask
  • Optoma EH504 | User manual - Page 53
    USING THE PROJECTOR The projector is setup for remote management. The LAN / RJ45 function displays as follows: Information page Main page Tool page Contact IT helpdesk English 53
  • Optoma EH504 | User manual - Page 54
    projector so called "RS232 by TELNET" for LAN / RJ45 interface. Quick Start-Guide for "RS232 by Telnet" ‡‡ Check and get the IP address on OSD of the projector ±± (ttt.xxx.yyy.zzz: IP-Address of the projector) 3. If Telnet-Connection ready, and user can have RS232 command input, then "Enter" key
  • Optoma EH504 | User manual - Page 55
    startup screen. If changes are made, they will take effect the next time the projector is powered on. ‡‡ Default: The default startup screen. ‡‡ Neutral: Logo is not displayed on startup screen. ‡‡ User: Use stored picture from "Logo Capture" function. Logo Capture Press to capture an image
  • Optoma EH504 | User manual - Page 56
    message. ‡‡ Off: Choose "Off" to show the "searching" message. Keypad Lock When the keypad lock function is "On", the Keypad will be locked. However, the projector can be operated by the remote control. By selecting "Off", you will be able to reuse the Keypad. Display Mode Lock Choose "On" or "Off
  • Optoma EH504 | User manual - Page 57
    USING THE PROJECTOR Options menu OPTIONS Background Color Wall Color Remote Settings 12V Trigger Beep Advanced Lamp Settings Blue Off Off Background Color Use this feature to display a "Black", "Red", "Blue", "Green", or "White", screen when no signal is available. Wall Color
  • Optoma EH504 | User manual - Page 58
    OPTIONS Optional Filter Settings Information Reset Exit Information Display the projector information. S/N Number F/W Version Information Current Input Source Resolution Refresh Rate Lamp Hours Bright Eco Dynamic Eco+ Filter Hour Projector ID IP Address Network Status Connected Exit Exit Choose
  • Optoma EH504 | User manual - Page 59
    USING THE PROJECTOR Options lamp settings menu Lamp Hour OPTIONS Lamp Settings Lamp Reminder Lamp Mode Lamp Reset On Bright Exit Lamp Hour Display the projection time. Lamp Reminder Choose this function to show or to hide the warning message when the changing lamp message is displayed. The
  • Optoma EH504 | User manual - Page 60
    USING THE PROJECTOR Options remote settings menu User 1 OPTIONS Remote Settings Test Pattern User 2 Zoom User 3 IR Function Info. On Exit USER 1 Assign the default function for USER1. The default value is "Test Pattern". User 1 Test Pattern ‡ ‡ USER 2 Press into the next menu and then
  • Optoma EH504 | User manual - Page 61
    the quick resume setting. ‡‡ On: If the projector is accidentally turned off, this feature allows the projector to be instantly powered on again, if selected within a period of 100 seconds. ‡‡ Off: The fan will start cooling the system after 10 seconds when user turns off the projector. English 61
  • Optoma EH504 | User manual - Page 62
    < 0.5W. ‡‡ ‡‡ Exit If the "Signal Power On" option is turned "On" or the "Audio Out (Standby)" option is turned "On", the power consumption of the projector in standby mode will be over 3W. The fans will still run in active standby if audio loop through / signal power on is enabled. Choose
  • Optoma EH504 | User manual - Page 63
    USING THE PROJECTOR Options optional filter settings menu OPTIONS Optional Filter Settings Filter usage Hours Optional Filter Installed Filter Reminer Filter Reset Yes 500 hr Exit Filter Usage
  • Optoma EH504 | User manual - Page 64
    Turn on your 3D glasses. Please refer to the 3D glasses user manual on how to operate the 3D glasses. 5. Your projector will automatically display 3D from a 3D Blu-ray. For 3D on the 3D glasses you have you will either need to select DLP Link or VESA in the menu. VESA glasses come with an emitter that
  • Optoma EH504 | User manual - Page 65
    the end of use, a warning message will appear on the screen. Lamp Warning Lamp life exceeded. When you see this message, please contact your local reseller or service center to change the lamp as soon as possible. Make sure the projector has been cooled down for at least 30 minutes before changing
  • Optoma EH504 | User manual - Page 66
    previous steps. 10. Turn on the projector and reset the lamp timer. 11. Lamp Reset: (i) Press "Menu"  (ii) Select "OPTIONS"  (iii) Select "Lamp Settings"  (iv) Select "Lamp Reset"  (v) Select "Yes". Note: ‡‡ ‡‡ The projector cannot be turned on if the lamp cover has not been placed back on
  • Optoma EH504 | User manual - Page 67
    the dust filter every three months. Clean it more often if the projector is used in a dusty environment. Procedure: 1. Switch off the power to the projector by pressing the " " button on the remote control or the projector Keypad. 2. Disconnect the power cord. 3. Remove the dust filter carefully
  • Optoma EH504 | User manual - Page 68
    additional information Compatible resolutions Digital compatibility B0/Established Timing B0/Standard Timing 720 x 400 @ 70Hz XGA / WXGA: 640 x 480 @ 60Hz 640 x 480 @ 67Hz 640 x 480 @ 72Hz 640 x 480 @ 75Hz 800 x 600 @ 56Hz 800 x 600 @ 60Hz 800 x 600 @ 72Hz 800 x 600 @ 75Hz 832 x 624 @ 75Hz
  • Optoma EH504 | User manual - Page 69
    ADDITIONAL INFORMATION True 3D video compatibility HDMI 1.4a 3D Input Input resolution HDMI 1.3 Input timing 1280 x 720P @ 50Hz 1280 x 720P @ 60Hz 1280 x 720P @ 50Hz 1280 x 720P @ 60Hz 1920 x 1080i @ 50 Hz 1920 x 1080i @ 60 Hz 1920 x 1080P @ 24 Hz 1920 x 1080P @ 24 Hz 1920 x 1080i @ 50Hz 1920
  • Optoma EH504 | User manual - Page 70
    ADDITIONAL INFORMATION Vertical + (Max) (A) cm 52.6 Lens Shift Range PJ lens Center to top of image Vertical (Min) (B) (D) = (A) - (B) Vertical range at any Horizontal position cm cm cm 44.9 7.7 N/A Image Shift Range Horizontal + Horizontal - (Right) cm (Left) cm 0.0 0.0 70.1 59
  • Optoma EH504 | User manual - Page 71
    ADDITIONAL INFORMATION Vertical + (Max) (A) cm 52.0 57.8 72.2 86.7 101.1 115.6 130.0 144.5 173.3 216.7 260.0 288.9 361.1 433.4 Lens Shift Range PJ lens Center to top of image Vertical (Min) (B) (D) = (A) - (B) Vertical range at any Horizontal position cm cm cm 44.3 7.7 N/A 49.3 8.5
  • Optoma EH504 | User manual - Page 72
    ADDITIONAL INFORMATION Vertical + (Max) (A) cm 54.5 60.5 75.7 90.8 105.9 121.1 136.2 151.3 181.6 227.0 272.4 302.6 378.3 453.9 Lens Shift Range PJ lens Center to top of image Vertical (Min) (B) Vertical Shift Range Vertical range at any Horizontal position cm cm cm 46.6 7.9 N/A 51.8
  • Optoma EH504 | User manual - Page 73
    ADDITIONAL INFORMATION Determining the lens shift center position Vertical Lens Shift Center 1. Image must be at the center of its Horizontal shift before adjusting the image to the center of its Vertical shift. 2. Adjust the V. Shift until the image reaches the maximum shift range towards the
  • Optoma EH504 | User manual - Page 74
    and ceiling mount installation 1. To prevent damage to your projector, please use the Optoma ceiling mount. 2. If you wish to use a third party ceiling mount kit, please ensure the screws used to attach a mount to the projector meet the following specifications: ‡‡ Screw type: M4*3 ‡‡ Minimum screw
  • Optoma EH504 | User manual - Page 75
    FIFO: Disable Projector Return (Pass): P Projector Return (Fail): F XX=01-99, projector's ID, XX=00 is for all projectors Note: 2 (XGA only) VGA2 Component (XGA only) S-Video (XGA only) Video Presentation Bright Movie sRGB User Blackboard DICOM SIM. 3D n = -50 (a=2D 35 30) ~ 50 (a=35 30) n
  • Optoma EH504 | User manual - Page 76
    ADDITIONAL INFORMATION 232 ASCII Code ~XX35 8 ~XX35 10 ~XX35 11 ~XX36 4 ~XX36 1 ~XX36 2 ~XX36 3 ~XX37 1 ~XX37 2 ~XX37 3 ~XX37 4 ~XX24 n ~XX25 n ~XX26 n ~XX27 n ~XX28 n ~XX29 n ~XX517 1 ~XX509 ~XX327 n ~XX333 n ~XX339 n ~XX328 n ~XX334 n HEX Code 7E 30 30 33 35 20 38 0D 7E 30 30 33 35 20 31 30 0D
  • Optoma EH504 | User manual - Page 77
    + Up+ Down+ Right+ Left+ Up+ Down+ Right+ Left+ Up+ Down+ Right+ Left+ Up+ Down+ Reset Off Light Yellow Light Green Light Blue Pink Gray DLP-Link VESA 3D Off (0/2 for backward compatible) 3D L R Auto SBS Top and Bottom Frame sequential On Off English German French Italian Spanish Portuguese Polish
  • Optoma EH504 | User manual - Page 78
    ) ~nnnn = ~0000 (a=7E 30 30 30 30) ~9999 (a=7E 39 39 39 39) Projector ID n = 00 (a=30 30) ~ 99 (a=39 39) Internal Speaker Off On Mute On Off 10 (a=31 30) Audio Input Default Audio1 Audio2 Logo Default User Neutral Logo Capture Closed Captioning Off cc1 cc2 Crestron Off On
  • Optoma EH504 | User manual - Page 79
    30 31 31 30 20 32 0D 7E 30 30 31 31 30 20 33 0D 7E 30 30 31 31 30 20 34 0D Lamp Reminder Lamp Mode Description On Off On Off On HDMI1 HDMI2 HDMI3 VGA1 VGA2 (XGA only) S-Video (XGA only) Video On Off (0/2 for backward compatible) On
  • Optoma EH504 | User manual - Page 80
    30 0D ~XX140 47 7E 30 30 31 34 30 20 34 37 0D SEND from projector automatically 232 ASCII Code HEX Code Function when Standby/Warming/Cooling/Out of Range/Lamp fail/Fan Lock/Over Temperature/ Lamp Hours Running Out/Cover Open Description Yes Yes No (0/2 for backward compatible) Off 300 hrs
  • Optoma EH504 | User manual - Page 81
    20 31 1D Information Projector Return Description OKdddd dddd: FW version Okeeeee eeeee = 2 Bright n = 3 Movie n = 4 sRGB n = 5 User n= 7 Blackboard n = 12 DICOM SIM. n = 9 3D OKn Front-Ceiling n = 3 Rear-Ceiling a = 0 Off a = 1 On bbbbb: Lamp Hour cc = Source cc = 00 None cc = 02 VGA1 cc = 03 VGA2
  • Optoma EH504 | User manual - Page 82
    0D 7E 30 30 33 35 36 20 31 0D 7E 30 30 33 35 38 20 31 0D Closed Captioning AV Mute Mute Current Lamp Watt Projector Return Description OKn n = 2 XGA n = 3 WXGA n = 4 1080p OKbbbb bbbb: LampHour OKbbbbb bbbbb: (5 digits) Total
  • Optoma EH504 | User manual - Page 83
    -key definition Description Power on / off Press to turn on / off the projector. Switch Press to switch the USB mouse on / off. Freeze Press to unhide the screen picture and turn off / on audio. Press to freeze the projector image. Press to momentarily turn off / on the audio. L R Up arrow
  • Optoma EH504 | User manual - Page 84
    2 3D/3 HDMI/4 VGA/5 Video/6 User 1/7 User 2/8 User 3/9 Source / 0 Re-Sync Description projector supports Dynamic Eco / Image Care features and AV Mute is pressed, the power consumption of the lamp becomes 30%. Remote mouse feature simulation specification ‡‡ The remote mouse feature is supported
  • Optoma EH504 | User manual - Page 85
    to open the Information menu. ‡‡ Information button functions only when no input source is detected. S/N Number F/W Version Information Current Input Source Resolution Refresh Rate Lamp Hours Bright Eco Dynamic Eco+ Filter Hour Projector ID IP Address Network Status Connected Exit English 85
  • Optoma EH504 | User manual - Page 86
    ADDITIONAL INFORMATION Troubleshooting If you experience a problem with your projector, please refer to the following information. If a problem persists, please contact your local reseller or service center. Image problems No image appears on-screen ‡‡ Ensure all the cables and power connections
  • Optoma EH504 | User manual - Page 87
    may make a loud popping sound. If this happens, the projector will not turn on until the lamp module has been replaced. To replace the lamp, follow the procedures in the "Replacing the Lamp" section on pages 65-66. Remote control problems If the remote control does not work ‡‡ Check the operating
  • Optoma EH504 | User manual - Page 88
    warning indicators (see below) light up or flash, the projector will automatically shutdown: ‡‡ "LAMP" LED indicator is lit red and if "On / from the projector, wait for 30 seconds and try again. If the warning indicator lights up again, please contact your nearest service center for assistance
  • Optoma EH504 | User manual - Page 89
    the environment temperature is under 45 degree C. If the problem persists in spite of the above. Please contact a service center for repair. ‡‡ Fan failed: Warning! FAN LOCKED The projector will switch off automatically. Please contact a service center for repair. ‡‡ Power down timer active: Power
  • Optoma EH504 | User manual - Page 90
    - Mic 3.5mm (XGA only) - VGA Outputs - Audio 3.5mm - USB-A power - 12V trigger (XGA only) - RS232 Control - RJ45 - 3D Sync VESA - USB mouse / service Color reproduction 1073.4 Million color Scan rate - Horizontal Scan rate: 15.375 ~ 91.146 KHz - Vertical Scan rate: 24~ 85 Hz (120Hz for 3D
  • Optoma EH504 | User manual - Page 91
    ADDITIONAL INFORMATION Mechanical Installation orientation Dimensions Weight Environmental conditions Description Front, Rear, Front-Ceiling, Rear-Ceiling 369 mm (W) x 294.5 mm (D) x 123.26 mm (H) 4.6 Kg Operating: 5 ~ 40°C in Bright mode (normal mode) 10% to 85% humidity (noncondensing) Operating
  • Optoma EH504 | User manual - Page 92
    ADDITIONAL INFORMATION Optoma global offices For service or support, please contact your local office. USA 3178 Laurelview Ct. Fremont, CA 94538, USA www.optomausa.com 888-289-6786 510-897-8601 [email protected] Japan 3-25-18 0120-380-495 [email protected] www.os-worldwide.com Canada
  • Optoma EH504 | User manual - Page 93
    www.optoma.com
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
User manual
DLP
®
Projector