Optoma EH505 User Guide - Page 94

PJLink™ supported commands, Command, Description, Remark Parameter

Get Optoma EH505 PDF manuals and user guides View all Optoma EH505 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 94 highlights

Appendices Command Description Remark (Parameter) Config-URL Device's IP address LAN IP address is shown up if LAN IP address is valid. http://xxx.xxx.xxx. xxx/index.html Wireless LAN IP address is shown up if Wireless LAN IP address is valid. Revision The revision must follow a major.minor.micro scheme. The revision is only increased if the command protocol is modified. 1.0.0 v For wide screen resolution (WXGA), the compatibility support is dependent on Notebook/PC models. v This AMX function is only to support AMX Device Discovery. v The broadcast information only send out through valid interface. v Both LAN and Wireless LAN interfaces could be supported at the same time. v If "Beacon Validator" was used. Please take care below information. PJLink™ supported commands The table below shows commands to control the projector using the PJLink™ protocol. Command Description Remark (Parameter) Command POWR POWR? INPT Description Remark (Parameter) Power control 0 = Standby 1 = Power on Inquiry about the power state 0 = Standby 1 = Power on 2 = Cooling down 3 = Warming up INPT Input switching 11 = VGA1 English 94

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
English
94
Command
Description
Remark (Parameter)
Config-URL
Device’s IP address
LAN IP address is shown up if
LAN IP address is valid.
Wireless LAN IP address is
shown up if Wireless LAN IP
address is valid.
xxx/index.html
Revision
The revision must follow a
major.minor.micro scheme. The
revision is only increased if the
command protocol is modified.
1.0.0
v
For wide screen resolution (WXGA), the compatibility support is
dependent on Notebook/PC models.
v
This AMX function is only to support AMX Device Discovery.
v
The broadcast information only send out through valid interface.
v
Both LAN and Wireless LAN interfaces could be supported at
the same time.
v
If “Beacon Validator” was used. Please take care below
information.
PJLink™ supported commands
The table below shows commands to control the projector using the
PJLink™ protocol.
Command Description Remark (Parameter)
Command
Description
Remark (Parameter)
POWR
Power control
0 = Standby
1 = Power on
POWR?
Inquiry about the
power state
0 = Standby
1 = Power on
2 = Cooling down
3 = Warming up
INPT
INPT Input switching
11 = VGA1
Appendices