Optoma W416 User manual

Optoma W416 Manual

Get Optoma W416 PDF manuals and user guides View all Optoma W416 manuals
Add to My Manuals
Save this manual to your list of manuals

Optoma W416 manual content summary:

  • Optoma W416 | User manual - Page 1
    DLP® Projector User manual
  • Optoma W416 | User manual - Page 2
    Table of Contents SAFETY 4 Important Safety Instruction...4 3D Safety Information...5 Copyright...6 Disclaimer...6 Trademark Recognition projector...13 Connecting sources to the projector 14 Adjusting the projector image...15 Remote setup...16 USING THE PROJECTOR 18 Powering on / off the projector
  • Optoma W416 | User manual - Page 3
    information 55 Compatible resolutions...55 Image size and projection distance 56 Projector dimensions and ceiling mount installation 61 IR remote codes...62 Using the Information button...64 Troubleshooting...64 Warning indicators...66 Specifications...68 Optoma global offices...70 English 3
  • Optoma W416 | User manual - Page 4
    maintenance (servicing) instructions in the literature accompanying the appliance. Please follow all warnings, precautions and maintenance as recommended in this user's guide. Important Safety Instruction ‡‡ Do not block any ventilation openings. To ensure reliable operation of the projector and to
  • Optoma W416 | User manual - Page 5
    unit to cool down. Follow instructions as described on pages 53-54. ‡‡ This projector will detect the life of projector to cool down. ‡‡ When the lamp is approaching to the end of its life time, the message "Lamp life exceeded." will show on the screen. Please contact your local reseller or service
  • Optoma W416 | User manual - Page 6
    postural stability. It is recommended that users take frequent breaks to lessen the potential viewers. Accordingly, DO NOT place your 3D PROJECTOR near open stairwells, cables, balconies, or other rights reserved. Neither this manual, nor any of the countries. DLP , DLP Link and the DLP logo are
  • Optoma W416 | User manual - Page 7
    could void the user's authority, which is granted by the Federal Communications Commission, to operate this projector. Operation Conditions This & TTE Directive 1999/5/EC (if product has RF function) WEEE Disposal instructions Do not throw this electronic device into the trash when discarding. To
  • Optoma W416 | User manual - Page 8
    accessories Projector Power Switch Freeze L R Enter Page- Laser Page+ Keystone -+ Volume -+ 1 4 HDMI 7 User1 Source 2 Menu 5 VGA 8 User2 0 3 3D 6 Video 9 User3 Resync Remote control 2x AAA batteries Power lead  CD User Manual  Warranty Card*  Basic User Manual Documentation
  • Optoma W416 | User manual - Page 9
    INTRODUCTION Product Overview 12 34 56 7 11 10 9 48 15 12 13 10 14 Note: Do not block projector inlet or outlet air vents. No Item 1. Focus Ring 2. Zoom Ring 3. Lens Shift Ring 4. IR Receiver 5. Keypad 6. Input / Output 7. Power Socket 8. Speaker No Item 9 Lens
  • Optoma W416 | User manual - Page 10
    remote control. No Item 1. USB Power Out (5V 1A) Connector 2. VGA-OUT Connector 3. VGA2 In/YPbPr / Connector 4. HDMI 1 / MHL Connector 5. MOUSE / SERVICE Connector 6. Power Socket 7. HDMI 2 Connector No Item 8. RS-232 Connector 9. RJ-45 Connector 10. AUDIO-IN 1 Connector 11. AUDIO-IN
  • Optoma W416 | User manual - Page 11
    INTRODUCTION Keypad 1 2 11 3 10 4 9 8 7 65 No Item 1. Enter 2. Keystone Correction 3. Information 4. Re-Sync 5. Four Directional Select Keys 6. Temp LED No Item 7. Power 8. On/Standby LED 9. Lamp LED 10. Source 11. Menu English 11
  • Optoma W416 | User manual - Page 12
    7. Page - 8. Keystone - / + 9. Menu 10. Aspect Ratio 11. HDMI 12. User 2 13. User 1 14. Source No Item 15. Brightness Mode 16. Mouse On / Off 17. Mute On / Off 23. VGA 24. Video 25. User 3 26. Numeric Keypad (0-9) 27. Resync Note: Some keys may have no function for models that do
  • Optoma W416 | User manual - Page 13
    mount. The projector should be horizontal and not tilted either forwards/backwards or left/right. Any other orientation will invalidate the warranty and may shorten the lifetime of the projector lamp or the projector itself. For none standard installation advise please contact Optoma. English 13
  • Optoma W416 | User manual - Page 14
    SETUP AND INSTALLATION Connecting sources to the projector 4 1 3 2 5 6 14 15 13 9 10 12 11 8 7 MOLEX No Item 1. Audio In Cable 2. VGA Out Cable 3. VGA Cable 4. RCA Component Cable 5. MHL Cable 6. HDMI Cable 7. Power
  • Optoma W416 | User manual - Page 15
    the image height. 1. Locate the adjustable foot you wish to adjust on the underside of the projector. 2. Rotate the adjustable foot clockwise or counterclockwise to raise or lower the projector. Tilt-Adjustment Feet Tilt-Adjustment Ring Zoom, focus, and lens shift ‡‡ To adjust the image size
  • Optoma W416 | User manual - Page 16
    result in chemical leakage or explosion. Be sure to follow the instructions below. ‡‡ Do not mix batteries of different types. Different there are no obstacles between the remote control and the IR sensor on the projector that might obstruct the infra-red beam. ‡‡ Make sure the IR transmitter of
  • Optoma W416 | User manual - Page 17
    SETUP AND INSTALLATION Approx. 10° Approx. 15° English 17 3 3D 6 Video 9 User3 Resync 2 Menu 5 VGA 8 User2 0 1 4 HDMI 7 User1 Source Volume -+ Keystone -+ Page- Laser Page+ Enter R L Freeze Switch Power Power Switch Freeze L R Enter Laser + PageK-eystone - 1 PVaogleu+me + - 3
  • Optoma W416 | User manual - Page 18
    Securely connect the power lead and signal/source cable. When connected, the On/Standby LED will turn red. 3. Turn on the projector by pressing the " " either on the projector keypad or the remote control. 4. A start up screen will display in approximately 10 seconds and the On/Standby LED will be
  • Optoma W416 | User manual - Page 19
    the message will disaFprpeeezear after a period of time (by default after 10 seconds). When you press the " " button for the second time, the projector will shut down. L R 4. The cooling fans will continue to operate for about 10 seconds for the cooling cycle and the On/ Standby LED will
  • Optoma W416 | User manual - Page 20
    projector will automatically detect the source. 1. To open the OSD menu, press the key on the projector key on the projector keypad or the on the projector keypad or key on the projector keypad or the projector keypad or the "Menu" key on the remote control. The OSD menu will close and the projector
  • Optoma W416 | User manual - Page 21
    USING THE PROJECTOR OSD Menu tree Main Menu Sub Menu Sub Menu 2 Sub Menu 3 Sub model] Color Settings Color Matching Color Hue Saturation Gain Values Presentation Bright Cinema Game sRGB DICOM SIM. User 3D Off [Default] Blackboard Light Yellow Light Green Light Blue Pink Gray -50~50 -50~50
  • Optoma W416 | User manual - Page 22
    USING THE PROJECTOR Main Menu Sub Menu Sub Menu 2 Sub Menu 3 Sub Menu 4 Color Settings Color Matching RGB depends on signal) [Default: 0] 0~31 [Default: 0] -5~5 (depends on signal) [Default: 0] -5~5 (depends on signal) [Default: 0] Bright Eco. Dynamic Eco+ Off DLP-Link [Default] IR 22 English
  • Optoma W416 | User manual - Page 23
    PROJECTOR SBS Top and Bottom Frame Sequential On Off [Default] 4:3 16:9 16:10 [WXGA / WUXGA models] LBX [except SVGA / XGA models] Native Auto 0~10 [Default: 0] -5~25 [ [Default depednds by connector] Off [Default] On (X416/W416/EH416/WU416) Front [Default] Rear Ceiling-top Rear-top English 23
  • Optoma W416 | User manual - Page 24
    USING THE PROJECTOR Main Menu Sub Menu Screen Type Sub Menu 2 [WXGA / WUXGA models] Lamp Settings Lamp Reminder Lamp Reset Filter Usage Hours Optional Filter Installed Sub Menu 3 Filter Settings Filter Reminder Setup Filter Reset Direct Power On
  • Optoma W416 | User manual - Page 25
    USING THE PROJECTOR Main Menu Sub Menu Sub Menu 2 HDMI Link Sub Menu 3 HDMI Link Settings Inclusive of TV Power On Link* Power Off Link Test Pattern Test
  • Optoma W416 | User manual - Page 26
    Main Menu Sub Menu Sub Menu 2 Sub Menu 3 Remote Settings [depends on remote] User3 Projector ID Setup Options Language Sub Menu 4 Values HDMI 2 Test Pattern LAN Brightness Contrast Sleep Timer [Default] Color Matching Color Temperature Gamma Projection Lamp Settings Zoom
  • Optoma W416 | User manual - Page 27
    USING THE PROJECTOR Main Menu Sub Menu Sub Menu 2 Closed Captioning Sub Menu 3 Menu Settings Menu Location Default] Custom Off [Default] On Off [Default] On Off [Default] On Off [Default] On Default [Default] Neutral User Cancel [Default] Yes None [Default] Blue Red Green Grey Logo English 27
  • Optoma W416 | User manual - Page 28
    USING THE PROJECTOR Main Menu Setup Sub Menu Reset LAN Sub Menu 2 Reset OSD Reset to Default Network Status MAC Address DHCP IP Address Subnet Mask Gateway DNS
  • Optoma W416 | User manual - Page 29
    Mode Power mode(standby) Lamp Hours Information Network Status IP Address Projector ID Filter Usage Hours Brightness Mode FW Version Sub Menu 2 set to a specific input source, the phase, frequency items will appear for user to manually tune and saved in settings. When you made the changes on the "
  • Optoma W416 | User manual - Page 30
    USING THE PROJECTOR ‡‡ 3D: To experience the 3D effect, you need to have 3D glasses. Make sure your PC/portable device has a 120 Hz signal output quad buffered
  • Optoma W416 | User manual - Page 31
    USING THE PROJECTOR RGB, or YUV. ‡‡ Color Space (HDMI input only): select an appropriate color matrix type from the following: auto, RGB(0-255), RGB(16-235), and YUV. ‡‡ White Level: Allow user to adjust White Level when inputting Video signals. ‡‡ Black Level: Allow user to adjust Black Level
  • Optoma W416 | User manual - Page 32
    enhanced for Wide screen TV. ‡‡ 16:10 (for WXGA and WUXGA models only): This format is for 16:10 input sources, like :1 content (include Anamorphic DVD and HDTV film source) that supports anamorphic wide is enhanced for 16x9 Display in a wide 2. projector image correctly on the screen. 32 English
  • Optoma W416 | User manual - Page 33
    USING THE PROJECTOR XGA scaling table: Source 4x3 16x9 Native Auto 480i/p 576i/p 768 1024 768 1024 576 1024 614 1024 640 1024 576 1024 576 1024 576 1024 576 Note: ‡‡ Supported screen type 16:9 (1280x720), 16:10 (1280x800). ‡‡ When screen type is 16:9, the16x10 format becomes
  • Optoma W416 | User manual - Page 34
    USING THE PROJECTOR WXGA auto mapping rule (screen type 16x10): Auto 4:3 Wide Laptop SDTV HDTV Input resolution H-resolution V-resolution 640 480 800 600 1024 768 1280 1024 1400
  • Optoma W416 | User manual - Page 35
    USING THE PROJECTOR WXGA auto mapping rule (screen type 16x9): Auto 4:3 Wide Laptop SDTV HDTV 1080P scaling table: Input resolution H-resolution V-resolution 640 480 800 600 1024 768
  • Optoma W416 | User manual - Page 36
    USING THE PROJECTOR WUXGA scaling table for 1920x1200 DMD (screen type 16x10): Note: ‡‡ Supported screen type 16:10 (1920x1200), 16:9 -If source is 16:10, the screen type will be scaled to 1920x1200. WUXGA auto mapping rule (screen type 16x10): Auto 4:3 Wide Laptop SDTV HDTV Input resolution
  • Optoma W416 | User manual - Page 37
    USING THE PROJECTOR WUXGA scaling table for 1920x1200 DMD (screen type 16x9): 16 : 9 screen 16:10, the screen type will be scaled to 1920x1200 and cut 1920x1080 area to display. WUXGA auto mapping rule (screen type 16x9): Auto 4:3 Wide Laptop SDTV HDTV Input resolution H-resolution V-
  • Optoma W416 | User manual - Page 38
    menu Audio Input The default audio settings are on the side panel of the projector. Use this option to reassign the available Audio Input to the selected image source , and rear-top. Setup screen type menu Screen Type (for WXGA and WUXGA models only) Choose the screen type from 16:9 and 16:10. Setup
  • Optoma W416 | User manual - Page 39
    projector will automatically power on when a signal is detected, without pressing the "Power" key on the projector consumption of the projector in standby mode the projector. The projector will the projector. The projector will projector is accidentally turned off, this feature allows the projector
  • Optoma W416 | User manual - Page 40
    < 0.5W. Note: ‡‡ If the "Signal Power On*" option is turned "On" or the "Audio Out (Standby)" option is turned "On", the power consumption of the projector in standby mode will be over 3W. ‡‡ The fans will still run in active standby if "Signal Power On" is enabled. ‡‡ *Optional feature depends on
  • Optoma W416 | User manual - Page 41
    matching, color temperature, gamma, projection, lamp settings, zoom, freeze, and MHL. Setup projector ID menu Projector ID ID definition can be set up by menu (range 0-99), and allow user control an individual projector by using RS232 command. Setup options menu Language Select the multilingual OSD
  • Optoma W416 | User manual - Page 42
    desired startup screen. If changes are made, they will take effect the next time the projector is powered on. ‡‡ Default: The default startup screen. ‡‡ Neutral: Logo is not displayed on startup screen. ‡‡ User: Use stored picture from "Logo Capture" function. Logo Capture Use to capture an image
  • Optoma W416 | User manual - Page 43
    address. Open the web browser in your PC and type in the projector's IP address ("Network > LAN > IP Address"). Enter the user name and password, and click "Login". The projector's configuration web interface opens. ‡‡ The default user name and password is "admin". ‡‡ The steps in this section is
  • Optoma W416 | User manual - Page 44
    > LAN"). 3. Open Network and Sharing Center page on your PC, and assign the identical network parameters to your PC as set on projector. Click "OK" to save the parameters. 4. Reset Open the web browser on your PC and type in to the URL field the IP address, assigned
  • Optoma W416 | User manual - Page 45
    /english/ For more detailed information about the various types of external devices which can be connected to the LAN / RJ45 port and remote control the projector, as well as the supported commands for these external devices, please contact the Support-Service directly. English 45
  • Optoma W416 | User manual - Page 46
    LAN RJ45 1. Connect an RJ45 cable to RJ45 ports on the projector and the PC (laptop). 2. On the PC (Laptop), select Start > Control Panel > Network Connections. 3. Right-click on the Local Area Connection, and select Property. 4. In
  • Optoma W416 | User manual - Page 47
    5. Click "Properties". 6. Type in the IP address and Subnet mask, then press "OK". 7. Press the "Menu" button on the projector. 8. Open on projector Network > LAN. 9. Enter the following connection parameters: ±± DHCP: Off ±± IP Address: 192.168.0.100 ±± Subnet Mask: 255.255.255.0 ±± Gateway
  • Optoma W416 | User manual - Page 48
    USING THE PROJECTOR 13. Press "Enter". The projector is setup for remote management. The LAN / RJ45 function displays as follows: Information page Main page Tool page 48 English
  • Optoma W416 | User manual - Page 49
    projector so called "RS232 by TELNET" for LAN / RJ45 interface. Quick Start-Guide for "RS232 by Telnet" ‡‡ Check and get the IP address on OSD of the projector ±± (ttt.xxx.yyy.zzz: IP-Address of the projector) 3. If Telnet-Connection ready, and user can have RS232 command input, then "Enter" key
  • Optoma W416 | User manual - Page 50
    USING THE PROJECTOR Specification for "RS232 by TELNET": 1. Telnet: TCP. 2. Telnet port: 23 (for more detail, kindly please get contact with the service agent or team). 3. Telnet utility: Windows "TELNET.exe" (console mode). 4. Disconnection for RS232-by-Telnet control normally: Close 5. Windows
  • Optoma W416 | User manual - Page 51
    you have inserted 3D content or selected the 3D channel. 4. Turn on your 3D glasses. Please refer to the 3D glasses user manual on how to operate the 3D glasses. 5. Your projector will automatically display 3D from a 3D Blu ray. For 3D via a set top box or PC, you will be required to
  • Optoma W416 | User manual - Page 52
    screen. Warning Lamp Warning Lamp life exceeded. When you see this message, please contact your local reseller or service center to change the lamp as soon as possible. Make sure the projector has been cooled down for at least 30 minutes before changing the lamp. Warning: If ceiling mounted, please
  • Optoma W416 | User manual - Page 53
    up the lamp handle. 4 8. Remove the lamp module carefully. 5 9. To replace the lamp module, reverse the previous steps. 10. Turn on the projector and reset the lamp timer. Lamp Reset: (i) Press "Menu" > (ii) Select "Setup" > (iii) Select "Lamp Settings" > (iv) Select "Lamp Reset" > (v) Select "Yes
  • Optoma W416 | User manual - Page 54
    MAINTENANCE Note: The screw on the lamp cover and the lamp cannot be removed. The projector cannot be turned on if the lamp cover has not been placed back on the projector. Do not touch the glass area of the lamp. Hand oil can cause the lamp shatter. Use a dry cloth to clean
  • Optoma W416 | User manual - Page 55
    /Detail Timing XGA/WXGA: 1440x900 @ 60Hz 1024x768 @ 120Hz 1280x800 @ 60Hz 1280x1024 @ 60Hz 1680x1050 @ 60Hz 1280x720 @ 60Hz 1280x720 @ 120Hz 1600x1200 @ 60Hz 1080P/WUXGA: 1280 x 720 @ 60Hz 1280 x 800 @ 60Hz 1280 x1024 @ 60Hz 1400 x 1050 @ 60Hz 1600 x 1200 @ 60Hz 1280 X 768 @ 60Hz 1440 x 900 @ 60Hz
  • Optoma W416 | User manual - Page 56
    is field sequential Note: ‡‡ ‡‡ ‡‡ If 3D input is 1080p@24hz, the DMD should replay with integral multiple with 3D mode. Support NVIDIA 3DTV Play if there is no patent fee from Optoma 1080i@25hz and 720p@50hz will run in 100 hz; other 3D timing will run in 120hz. 1080i@25hz and
  • Optoma W416 | User manual - Page 57
    Vertical + (Max) (A) cm 52.6 70.1 87.6 105.2 122.7 140.2 157.7 175.3 210.3 262.9 315.5 350.5 438.2 525.8 Lens Shift Range PJ lens Center to top of image Vertical (Min) (B) (D) = (A) - (B) Vertical range at any Horizontal position cm cm cm 44.9 7.7 N/A 59.8 10.3 N/A 74.8 12.9 N/A 89
  • Optoma W416 | User manual - Page 58
    ADDITIONAL INFORMATION Vertical + (Max) (A) cm 52.0 57.8 72.2 86.7 101.1 115.6 130.0 144.5 173.3 216.7 260.0 288.9 361.1 433.4 Lens Shift Range PJ lens Center to top of image Vertical (Min) (B) Vertical Shift Range Vertical range at any Horizontal position cm cm cm 44.3 7.7 N/A 49.3
  • Optoma W416 | User manual - Page 59
    ADDITIONAL INFORMATION Vertical + (Max) (A) cm 54.5 60.5 75.7 90.8 105.9 121.1 136.2 151.3 181.6 227.0 272.4 302.6 378.3 453.9 Lens Shift Range PJ lens Center to top of image Vertical (Min) (B) Vertical Shift Range Vertical range at any Horizontal position cm cm cm 46.6 7.9 N/A 51.8
  • Optoma W416 | User manual - Page 60
    the Base to the Center of Projection Lens needs to be added to each Vertical Lens Shift value. Zoom ratio is 1.6x. V+ 2 V V- A B 3 1 5.4 cm C 1. Center of projector lens. 2. Projection image while lens shift at the highest postion 3. Vertical shift range : 10% V 60 English
  • Optoma W416 | User manual - Page 61
    and ceiling mount installation 1. To prevent damage to your projector, please use the Optoma ceiling mount. 2. If you wish to use a third party ceiling mount kit, please ensure the screws used to attach a mount to the projector meet the following specifications: ‡‡ Screw type: M4*3 ‡‡ Minimum screw
  • Optoma W416 | User manual - Page 62
    Press to switch the USB mouse on / off. Freeze Press to hide / unhide the screen picture and turn off / on audio. Press to freeze the projector image. Press to momentarily turn off / on the audio. L R Up arrow Left arrow Right arrow Down arrow Enter Enter PageLaser Use as mouse left click
  • Optoma W416 | User manual - Page 63
    or exit the on-screen display menus for projector. ‡‡ Use as numeric keypad number "2". ‡‡ Press to manually select a 3D mode that matches your 3D Press to choose composite video source. ‡‡ Use as numeric keypad number "6". ‡‡ User defined keys. Please see page 41 to setup. ‡‡ Use as numeric keypad
  • Optoma W416 | User manual - Page 64
    Information menu. button on the keypad to open the Troubleshooting If you experience a problem with your projector, please refer to the following information. If a problem persists, please contact your local reseller or service center. Image problems No image appears on-screen ‡‡ Ensure all the
  • Optoma W416 | User manual - Page 65
    input signal is HDMI 1.3 2D (1080i side-by-side half), press "3D" button and switch to "SBS". Other problems The projector stops responding to all controls ‡‡ If possible, turn off the projector, then unplug the power cord and wait at least 20 seconds before reconnecting power. Lamp burns out or
  • Optoma W416 | User manual - Page 66
    red and if "On/Standby" indicator flashes amber. Unplug the power cord from the projector, wait for 30 seconds and try again. If the warning indicator light up or flash, please contact your nearest service center for assistance. LED lightning messages Message Standby state (Input power cord) Power
  • Optoma W416 | User manual - Page 67
    the environment temperature is under 45 degree C. If the problem persists in spite of the above. Please contact a service center for repair. ‡‡ Fan failed: Warning FAN LOCKED The projector will switch off automatically Please contact a service center for repair. ‡‡ Out of display range: HDMI Out
  • Optoma W416 | User manual - Page 68
    WUXGA for WXGA 16:10 - 1920x1200 @60hz only supported for RB (Reduced Blanking) - Manual zoom and manual .66"~301.15" 1080p format: - 26.2"~301.1" WUXGA format: - 26.94"~302.9" (focus range with 1.3m~9.4m (focus range with optimized @1.873m) WUXGA format: - 1.30m~9.2m (focus range with optimized
  • Optoma W416 | User manual - Page 69
    current Description - Horizontal scan rate: 15.375~91.146 KHz - Vertical scan rate: 24~ 85 Hz (120Hz for 3D featured projector) Yes, 10W 100 - 240V ±10 50/60Hz 2.5-1.0 A Mechanical Installation orientation Dimensions Weight Environmental conditions Description Desktop/Front, Desktop/Rear, Ceiling
  • Optoma W416 | User manual - Page 70
    ADDITIONAL INFORMATION Optoma global offices For service or support, please contact your local office. USA 3178 Laurelview Ct. Fremont, CA 94538, USA www.optomausa.com 888-289-6786 510-897-8601 [email protected] Japan 3-25-18 0120-380-495 [email protected] www.os-worldwide.com Canada
  • Optoma W416 | User manual - Page 71
    www.optoma.com
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
User manual
DLP
®
Projector