Optoma W416 User manual - Page 65

Optoma W416 Manual

Get Optoma W416 PDF manuals and user guides View all Optoma W416 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 65 highlights

ADDITIONAL INFORMATION The image is stretched when displaying 16:9 DVD title ‡‡ When you play anamorphic DVD or 16:9 DVD, the projector will show the best image in 16: 9 format on projector side. ‡‡ If you play the LBX format DVD title, please change the format as LBX in projector OSD. ‡‡ If you play 4:3 format DVD title, please change the format as 4:3 in projector OSD. ‡‡ Please setup the display format as 16:9 (wide) aspect ratio type on your DVD player. Image is too small or too large ‡‡ Adjust the zoom ring on the top of the projector. ‡‡ Move the projector closer to or further from the screen. ‡‡ Press "Menu" on the projector panel, go to "Display --> Aspect Ratio". Try the different settings. Image has slanted sides: ‡‡ If possible, reposition the projector so that it is centered on the screen and below the bottom of the screen. ‡‡ Use "Display--> Geometric Correction --> V Keystone" and "Display--> Geometric Correction --> H Keystone" from the OSD to make an adjustment. Image is reversed ‡‡ Select "Setup--> Projection" from the OSD and adjust the projection direction. Blurry double image ‡‡ Press "3D" button and switch to "Off" to avoid normal 2D image is blurry double image. Two images, side-by-side format ‡‡ Press "3D" button and switch to "SBS" for input signal is HDMI 1.3 2D 1080i side-by-side. Image does not display in 3D ‡‡ Check if the battery of 3D glasses is drained. ‡‡ Check if the 3D glasses is turned on. ‡‡ When the input signal is HDMI 1.3 2D (1080i side-by-side half), press "3D" button and switch to "SBS". Other problems The projector stops responding to all controls ‡‡ If possible, turn off the projector, then unplug the power cord and wait at least 20 seconds before reconnecting power. Lamp burns out or makes a popping sound ‡‡ When the lamp reaches its end of life, it will burn out and may make a loud popping sound. If this happens, the projector will not turn on until the lamp module has been replaced. To replace the lamp, follow the procedures in the "Replacing the Lamp" section on pages 53-54. English 65

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
English
65
ADDITIONAL INFORMATION
The image is stretched when displaying 16:9 DVD title
When you play anamorphic DVD or 16:9 DVD, the projector will show the best image in 16: 9 format
±
on projector side.
If you play the LBX format DVD title, please change the format as LBX in projector OSD.
±
If you play 4:3 format DVD title, please change the format as 4:3 in projector OSD.
±
Please setup the display format as 16:9 (wide) aspect ratio type on your DVD player.
±
Image is too small or too large
Adjust the zoom ring on the top of the projector.
±
Move the projector closer to or further from the screen.
±
Press "Menu" on the projector panel, go to "Display --> Aspect Ratio". Try the different settings.
±
Image has slanted sides:
If possible, reposition the projector so that it is centered on the screen and below the bottom of the
±
screen.
Use "Display--> Geometric Correction --> V Keystone” and “Display--> Geometric Correction --> H
±
Keystone” from the OSD to make an adjustment.
Image is reversed
Select "Setup--> Projection" from the OSD and adjust the projection direction.
±
Blurry double image
Press "3D" button and switch to "Off" to avoid normal 2D image is blurry double image.
±
Two images, side-by-side format
Press "3D" button and switch to "SBS" for input signal is HDMI 1.3 2D 1080i side-by-side.
±
Image does not display in 3D
Check if the battery of 3D glasses is drained.
±
Check if the 3D glasses is turned on.
±
When the input signal is HDMI 1.3 2D (1080i side-by-side half), press "3D" button and switch to "SBS".
±
Other problems
The projector stops responding to all controls
If possible, turn off the projector, then unplug the power cord and wait at least 20 seconds before
±
reconnecting power.
Lamp burns out or makes a popping sound
When the lamp reaches its end of life, it will burn out and may make a loud popping sound.
If this
±
happens, the projector will not turn on until the lamp module has been replaced. To replace the lamp,
follow the procedures in the "Replacing the Lamp" section on pages
53-54
.