Panasonic AG-HPX600PJ Operating Instructions - Page 159

Maintenance and Inspection - Warning system, Message, Description, Measure

Get Panasonic AG-HPX600PJ PDF manuals and user guides View all Panasonic AG-HPX600PJ manuals
Add to My Manuals
Save this manual to your list of manuals

Page 159 highlights

rr Soft keyboard Message CANNOT CHANGE! CANNOT SET! INVALID VALUE! Chapter 10 Maintenance and Inspection - Warning system Description An attempt is made to enter a [PERSON] (user who enters the memo) when a text memo is not available. The entered value is invalid. Measure Enter the [TEXT] (text information) first. Change the input value. rr Hard disk drive (USB host mode) Message CANNOT ACCESS CARD! CANNOT ACCESS TARGET! CANNOT FORMAT! CANNOT RECOGNIZE HDD! CARD IS EMPTY! CANNOT COPY! FORMAT P2 CARD! LACK OF CAPACITY! HDD DISCONNECTED! MISMATCH COMPONENT! TOO MANY PARTITIONS! TOO MANY TARGETS! UNKNOWN DEVICE CONNECTED! VERIFICATION FAILED! Description Measure An error occurred while accessing the P2 card. Check the P2 card. An error occurred while accessing the connection target. Check the hard disk drive status or the connection. The hard disk drive cannot be initialized. Change the connected hard disk drive. The destination target cannot be properly recognized. Reboot the hard disk drive or connect another hard disk drive. The P2 card to copy is empty. The copy operation is not performed because the card is empty. A warning indicates that the copy operation cannot be The copy operation cannot be performed because the target performed at the hard disk drive → P2 import because the P2 P2 card is not empty. Format the card using a P2 device and card is already recorded. try again. Not enough space left on the hard disk drive. There is not enough space on the connected target, so use a new hard disk drive or formatted hard disk drive. The hard disk drive is disconnected. Reconnect the USB connection cable. If the hard disk drive does not operate properly, turn it off and turn it back on again. The copy operation cannot be performed because the P2 card capacities and models do not match between the source and Use the P2 cards of the same model, or import on a clip basis. the target. There are too many partitions. The maximum number of partitions is 23, so use a new hard disk drive or formatted hard disk drive. Multiple devices are connected. Disconnect the devices, turn off the camera, and then turn it back on again. A non-compatible DVD drive or other device is connected. Disconnect the devices, turn off the camera, and then turn it back on again. The compare check performed after copying failed. Copy the data again. - 159 -

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
– 159 –
Chapter 10 Maintenance and Inspection — Warning system
r
Soft keyboard
Message
Description
Measure
CANNOT CHANGE!
An attempt is made to enter a [PERSON] (user who enters
the memo) when a text memo is not available.
Enter the [TEXT] (text information) first.
CANNOT SET!
INVALID VALUE!
The entered value is invalid.
Change the input value.
r
Hard disk drive (USB host mode)
Message
Description
Measure
CANNOT ACCESS CARD!
An error occurred while accessing the P2 card.
Check the P2 card.
CANNOT ACCESS TARGET!
An error occurred while accessing the connection target.
Check the hard disk drive status or the connection.
CANNOT FORMAT!
The hard disk drive cannot be initialized.
Change the connected hard disk drive.
CANNOT RECOGNIZE HDD!
The destination target cannot be properly recognized.
Reboot the hard disk drive or connect another hard disk drive.
CARD IS EMPTY! CANNOT
COPY!
The P2 card to copy is empty.
The copy operation is not performed because the card is
empty.
FORMAT P2 CARD!
A warning indicates that the copy operation cannot be
performed at the hard disk drive
→
P2 import because the P2
card is already recorded.
The copy operation cannot be performed because the target
P2 card is not empty. Format the card using a P2 device and
try again.
LACK OF CAPACITY!
Not enough space left on the hard disk drive.
There is not enough space on the connected target, so use a
new hard disk drive or formatted hard disk drive.
HDD DISCONNECTED!
The hard disk drive is disconnected.
Reconnect the USB connection cable. If the hard disk drive
does not operate properly, turn it off and turn it back on again.
MISMATCH COMPONENT!
The copy operation cannot be performed because the P2 card
capacities and models do not match between the source and
the target.
Use the P2 cards of the same model, or import on a clip basis.
TOO MANY PARTITIONS!
There are too many partitions.
The maximum number of partitions is 23, so use a new hard
disk drive or formatted hard disk drive.
TOO MANY TARGETS!
Multiple devices are connected.
Disconnect the devices, turn off the camera, and then turn it
back on again.
UNKNOWN DEVICE
CONNECTED!
A non-compatible DVD drive or other device is connected.
Disconnect the devices, turn off the camera, and then turn it
back on again.
VERIFICATION FAILED!
The compare check performed after copying failed.
Copy the data again.