Panasonic CF-18FCAZXVM Notebook Computer - Page 44

Backing Up and Restoring Data

Get Panasonic CF-18FCAZXVM - Toughbook 18 Tablet PC Version PDF manuals and user guides
UPC - 092281844367
View all Panasonic CF-18FCAZXVM manuals
Add to My Manuals
Save this manual to your list of manuals

Page 44 highlights

Hard Disk Backup Function Select [2], enter the partition size (GB), and press Enter . • You can cancel this operation by pressing 0 . • The data partition size will be the maximum settable size less the number entered above. The maximum settable size will differ depending on models. [At the time of purchase] The usable hard disk area [After the backup area is created] The backup area Can be accessed from Windows (Two partitions). Cannot be accessed from Windows. 9 When the confirmation message is displayed, press Y . The backup area is then created. 10 When the message [You must reboot in order to enable the Backup function] appears, remove the recovery CD, and press any key to restart the computer. The computer is restarted, then the backup process will begin. 11 When the message [[Backup] is complete] appears, press Ctrl + Alt + Del to restart the computer. CAUTION Do not press Ctrl + Alt + Del until the message is displayed. 12 After logging on to Windows, a message will appear advising that a new device has been installed and that the computer must be restarted to enable the settings. Select [Yes] to restart the computer. NOTE The [Boot] menu in the Setup Utility is set to start up from the CD/DVD drive. Change this setting if necessary. The next time the backup or restore functions are executed, follow the procedure for [Backing Up and Restoring Data] ( below). Backing Up and Restoring Data CAUTION Before executing the backup function, execute a disk error check ( page 42). Do not interrupt the backup or restore functions before completion, for example by turning off the power or pressing Ctrl + Alt + Del , as this may prevent Windows from starting up, or may cause data to be lost so that the backup and restore functions cannot be executed. 1 Turn the computer on, and press F2 while [Panasonic] boot screen is displayed. The Setup Utility will start up. If a password has been set, enter the Supervisor Password or the User Password. 2 Select [Exit] menu, then select [Hard Disk Backup / Restore] and press çEnter . At the confirmation message, select [Yes] and press çEnter . Appendix 44

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
44
Appendix
Hard Disk Backup Function
9
When the confirmation message is displayed, press
Y
.
The backup area is then created.
10
When the message [You must reboot in order to enable the Backup function] appears, remove
the recovery CD, and press any key to restart the computer. The computer is restarted, then the
backup process will begin.
11
When the message [[Backup] is complete] appears, press
Ctrl
+
Alt
+
Del
to restart
the computer.
Do not
press
Ctrl
+
Alt
+
Del
until
the message is displayed.
CAUTION
The [Boot] menu in the Setup Utility is set to start up from the CD/DVD drive. Change this
setting if necessary.
The next time the backup or restore functions are executed, follow the procedure for [Back-
ing Up and Restoring Data] (
below).
NOTE
1
Turn the computer on, and press
F2
while [Panasonic] boot screen is displayed.
The Setup Utility will start up.
If a password has been set, enter the Supervisor Password or the User Password.
2
Select [Exit] menu, then select [Hard Disk Backup / Restore] and press
Enter
.
At the confirmation message, select [Yes] and press
Enter
.
Backing Up and Restoring Data
Before executing the backup function, execute a disk error check (
page 42).
Do not interrupt the backup or restore functions before completion, for example by turning
off the power or pressing
Ctrl
+
Alt
+
Del
, as this may prevent Windows from
starting up, or may cause data to be lost so that the backup and restore functions cannot be
executed.
CAUTION
12
After logging on to Windows, a message will appear advising that a new device has been
installed and that the computer must be restarted to enable the settings.
Select [Yes] to restart
the computer.
<To create a backup area and divide hard disk into two partitions, for OS and data>
Select [2], enter the partition size (GB), and press
Enter
.
• You can cancel this operation by pressing
0
.
• The data partition size will be the maximum settable size less the number entered above.
The maximum settable size will differ depending on models.
The usable hard disk area
[At the time of purchase]
[After the backup area is created]
The backup area
Cannot be accessed
from Windows.
Can be accessed from
Windows (Two partitions).