Panasonic EW3152W Instruction Manual - Page 17

measurement.

Get Panasonic EW3152W PDF manuals and user guides View all Panasonic EW3152W manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

Alarm function signals high blood pressure Blood pressure values for both systolic and diastolic readings are determined and indicated via a three-color LED system as being within normal or hypertensive ranges based on definitions and classification of blood pressure levels by the JNC 7. Moreover, when blood pressure is in the high range, the reading displayed on screen flashes on and off to alert user. According to JNC 7 Classification, values consistently in excess of 140 mmHg (Sys.) and/or 90 mmHg (Dia.) are considered to constitute high blood pressure. LED Color Diastolic (mmHg) Hypertension 140 (Stage 1, Stage 2) 120 90 Yellow Prehypertension 90 80 80 Green Normal 120 140 (mmHg) Systolic • If the measured blood Systolic blood pressure: pressure value is in the high 140mmHg or higher blood pressure region, the izoo • Diastolic blood pressure: values will blink for 90mmHg or higher approximately 12 seconds. (Only immediately after measurement) O (7) If measurements could not be taken properly The remeasure mark E will be displayed. When taking successive measurements, press the On/Off Start E button to switch off the blood pressure monitor once and stay quiet for 4 to 5 minutes, and then take the next measurement. Advice: In general, blood pressure measurements are lower for the second measurement because you are less nervous and are more tranquil. For people who easily get tense, measuring twice each time is very effective. When two measurements are taken, normally the smaller measurement is stored. When taking two measurements, always stay quiet for 4 to 5 minutes after the first measurement before taking the second measurement 17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
Alarm
function
signals
high
blood
pressure
Blood
pressure
values
for
both
systolic
and
diastolic
readings
are
determined
and
indicated
via
a
three
-color
LED
system
as
being
within
normal
or
hypertensive
ranges
based
on
definitions
and
classification
of
blood
pressure
levels
by
the
JNC
7.
Moreover,
when
blood
pressure
is
in
the
high
range,
the
reading
displayed
on
screen
flashes
on
and
off
to
alert
user.
According
to
JNC
7
Classification,
values
consistently
in
excess
of
140
mmHg
(Sys.)
and/or
90
mmHg
(Dia.)
are
considered
to
constitute
high
blood
pressure.
140
120
90
80
•
If
the
measured
blood
pressure
value
is
in
the
high
blood
pressure
region,
the
values
will
blink
for
approximately
12
seconds.
(Only
immediately
after
measurement)
LED
Color
Diastolic
(mmHg)
90
80
Green
120 140
(mmHg)
Systolic
Systolic
blood
pressure:
140mmHg
or
higher
iz
o
o
•
Diastolic
blood
pressure:
90mmHg
or
higher
O
(7)
If
measurements
could
not
be
taken
properly
E
The
remeasure
mark
E
will
be
displayed.
When
taking
successive
measurements,
press
the
On/Off
Start
button
to
switch
off
the
blood
pressure
monitor
once
and
stay
quiet
for
4
to
5
minutes,
and
then
take
the
next
measurement.
Advice:
In
general,
blood
pressure
measurements
are
lower
for
the
second
measurement
because
you
are
less
nervous
and
are
more
tranquil.
For
people
who
easily
get
tense,
measuring
twice
each
time
is
very
effective.
When
two
measurements
are
taken,
normally
the
smaller
measurement
is
stored.
When
taking
two
measurements,
always
stay
quiet
for
4
to
5
minutes
after
the
first
measurement
before
taking
the
second
measurement
17