Panasonic SA-XR55S SAXR55 User Guide - Page 16

Control guide Main unit [8, POWER] Press to switch the unit from on to standby mode or vice versa. In standby mode, the unit is still consuming a small amount of power. Standby indicator [^] When the unit is connected to the AC mains supply, this indicator lights up in standby mode and goes out when the unit is turned on. [SPEAKERS, A, B] For selecting speakers A or B. Turning the speakers off automatically engages the STEREO/2CH MIX mode (when listening through headphones, for example). [MULTI CONTROL, CANCEL] Press to enter Multi control or cancel. [ENTER] Enters setting in Multi control. [INPUT SELECTOR] For selecting input. Selects each setting in Multi control. [VOLUME] Volume control. Before use POWER SPEAKERS A B DUAL AMP BI-AMP BAND PRESET TUNE VCR 2 VIDEO IN L AUDIO IN R MULTI CONTROL ENTER INPUT SELECTOR CANCEL DOWN VOLUME UP PHONES Connections Settings Operations Basic Operations Remote control signal sensor [VCR 2] For a game player, etc. [DUAL AMP] Lights when the DUAL AMP function is activated. [BI-AMP] Lights when the BIAMP function is activated. [BAND] For switching between FM and AM. [PRESET] Press to allow preset station selection with [2 TUNE 1]. [2 TUNE 1] For tuning the radio and selecting preset stations. Press and hold until the frequency starts scrolling to start automatic tuning. Tuning stops when a station is found. [PHONES] Headphone jack. Plug type: 6.3 mm (1/4") stereo Avoid listening for prolonged periods of time to prevent hearing damage. Turn the speakers off when using the headphones. Display indicators [RE-MASTER] Lights when the multi-source re-master function is on. [MULTI CONTROL] When you press the [MULTI CONTROL, CANCEL] button and enter the settings the indicator lights. [SLEEP] Sleep timer indicator. [TUNED] A station is tuned. [ST] A stereo FM broadcast is tuned. [MONO] Lights when using the monaural mode. [M] Flashes during presetting. automatic [DIGITAL INPUT] • The channels contained in the digital input signal light. • No sound is output from a channel if the speaker is set to "_" (not connected) in "Speakers combination settings" (ápage 12) even if the channel indicator lights. L: Front left channel C: Center channel R: Front right channel LS: Surround left channel SB: Surround back channel RS: Surround right channel S: If the surround channel is monaural LFE (Low Frequency Effects): Deep-bass effect [PCM] Lights when the PCM FIX mode is set. RE-MASTER TUNED ST MONO M MULTI CONTROL SLEEP SPEAKERS A B BI-WIRE DIGITAL INPUT L CR 2CH MIX LS SB RS kHz PCM MHz S LFE SOUND MODE DIGITAL EX DTS -ES DTS 96/24 EX NEO:6 SFC PL x STEREO [- SPEAKERS - A , B , BI-WIRE ] Speaker indicators. A: Sound is output from speakers connected to the front A, surround, and center terminals. B: Sound is output only from speakers connected to the front B terminals. A, B: Sound is output from speakers connected to the front A, B, surround, and center terminals. A, B, BI-WIRE: Sound is output from speakers connected by Bi-wiring. General display Shows the input mode, radio frequency, and other general information. [2CH MIX] Lights when playing a multi-channel source in 2CH MIX mode. [kHz, MHz] Frequency unit indicators. kHz: AM, or PCM sampling frequency MHz: FM [SOUND MODE] The following light to indicate the source's input signal (multichannel digital signal) and the decoding format used. (ábelow) Reference SOUND MODE DIGITAL: Dolby Digital decoder is being used. PL : Dolby Pro Logic DIGITAL EX: Dolby Digital Surround EX decoder (Dolby Pro Logic decoder) is being used when decoder is being used. the input signal is Dolby Digital 5.1-channel or Dolby Digital Surround EX. PL : Dolby Pro Logic EX: Dolby Digital Surround EX decoder (Dolby Pro Logic decoder) is being used when the input signal is DTS. decoder is being used. DTS-ES: DTS-ES discrete or matrix decoder is being used. NEO:6: DTS NEO:6 matrix DTS: DTS decoder is being used. decoder is being used. DTS 96/24: DTS 96/24 decoder is being used. SFC: SFC matrix function is STEREO: 2-channel stereo decoder is being used. being used. RQT7994 • • 16 DIGITAL EX and EX are displayed only when "1 SPKR " is selected in "Surround back speaker settings". (ápage 12) PL is displayed when using Dolby Pro Logic with stereo (2-channel) sources and "SB " is set to "_" in "Speakers combination settings". (ápage 12)