Pioneer 917V-K Owner's Manual - Page 27

Character display LCD - reset

Get Pioneer 917V-K - AV Receiver PDF manuals and user guides View all Pioneer 917V-K manuals
Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

English Deutsch Français Italiano Nederlands Español Controls and displays 04 PHASE - Press to switch on/off Phase Control (page 10). ACOUSTIC EQ - Press to select an Acoustic Calibration EQ setting (page 31). DIALOG - Use to make dialog stand out when watching TV or a movie (page 33). SOUND RETRIEVER - Press to restore CD quality sound to compressed audio sources (page 33). 9 SHIFT Press to access the DVR controls (above the component control buttons) as well as some receiver controls. 10 INPUT SELECT Use to select the input source (use SHIFT for INPUT SELECT ). 11 SOURCE Press to turn on/off other components connected to the receiver (see page 47 for more on this). 12 Character display (LCD) This display shows information when transmitting control signals. The following commands are shown when you're setting the remote to control other components (see Controlling the rest of your system on page 47): SETUP - Indicates the setup mode, from which you choose the options below. PRESET - See Selecting preset codes directly on page 48. DIRECT F - See Direct function on page 49. ERASE - See Erasing one of the remote control button settings on page 48. RESET - See Erasing all of the remote control presets on page 48. READ ID - See Confirming preset codes on page 49. 13 RECEIVER Switches the remote to control the receiver (used to select the green commands above the number buttons (DIMMER, etc). Also use this button to set up surround sound (page 8, page 35). 14 VOL +/- Use to set the listening volume. 15 MUTE Mutes the sound or restores the sound if it has been muted (adjusting the volume also restores the sound). 16 EFFECT/CH SEL Press repeatedly to select a channel, then use +/- to adjust the level (see Tip on page 43). Also adjusts the level of the Advanced Surround effects, Dolby Pro Logic IIx Music, and Neo:6 Music parameters (page 29). You can then use the +/- buttons to make these adjustments. Operating range of remote control The remote control may not work properly if: • There are obstacles between the remote control and the receiver's remote sensor. • Direct sunlight or fluorescent light is shining onto the remote sensor. • The receiver is located near a device that is emitting infrared rays. • The receiver is operated simultaneously with another infrared remote control unit. 30 30 DOWN DOWN 7 m (23 ft) 27 En

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
Controls and displays
04
27
En
English
Français
Deutsch
Nederlands
Italiano
Español
PHASE
– Press to switch on/off Phase
Control (page 10).
ACOUSTIC EQ
– Press to select an
Acoustic Calibration EQ setting (page 31).
DIALOG
– Use to make dialog stand out
when watching TV or a movie (page 33).
SOUND RETRIEVER
– Press to restore CD
quality sound to compressed audio
sources (page 33).
9
SHIFT
Press to access the DVR controls (above the
component control buttons) as well as some
receiver controls.
10
INPUT SELECT
Use to select the input source (use
SHIFT
for
INPUT SELECT
).
11
SOURCE
Press to turn on/off other components
connected to the receiver (see page 47 for
more on this).
12
Character display (LCD)
This display shows information when
transmitting control signals.
The following commands are shown when
you’re setting the remote to control other
components (see
Controlling the rest of your
system
on page 47):
SETUP
– Indicates the setup mode, from
which you choose the options below.
PRESET
– See
Selecting preset codes
directly
on page 48.
DIRECT F
– See
Direct function
on page 49.
ERASE
– See
Erasing one of the remote
control button settings
on page 48.
RESET
– See
Erasing all of the remote
control presets
on page 48.
READ ID
– See
Confirming preset codes
on
page 49.
13 RECEIVER
Switches the remote to control the receiver
(used to select the green commands above the
number buttons (
DIMMER
, etc). Also use this
button to set up surround sound (page 8,
page 35).
14
VOL +/–
Use to set the listening volume.
15 MUTE
Mutes the sound or restores the sound if it has
been muted (adjusting the volume also
restores the sound).
16
EFFECT/CH SEL
Press repeatedly to select a channel, then
use
+/–
to adjust the level
(see
Tip
on
page 43). Also adjusts the level of the
Advanced Surround effects, Dolby Pro
Logic IIx Music, and Neo:6 Music
parameters (page 29). You can then use
the
+/–
buttons to make these
adjustments.
Operating range of remote control
The remote control may not work properly if:
•
There are obstacles between the remote
control and the receiver's remote sensor.
•
Direct sunlight or fluorescent light is
shining onto the remote sensor.
•
The receiver is located near a device that is
emitting infrared rays.
•
The receiver is operated simultaneously
with another infrared remote control unit.
30
30
7 m (23 ft)