Pioneer BDP-09FD Owner's Manual - Page 67

Problem Sound and picture are not synchronized. Check Is Output Terminal properly set? Is Lip Sync properly set? Remedy 07 Set Output Terminal properly (pages 21 and 44). Adjust the amount of audio delay with the Lip Sync setting (page 42). • No sound is output. • Sound is not output properly. Is the disc played back in slow motion? Is the disc played back in fast forward or fast reverse? Are the audio cables properly connected? No sound is output during slow motion play and forward and reverse scanning. • Connect the cable properly according to the connected devices (page 15). • Insert the cable firmly and all the way in. Is the audio cable damaged? If the cable is damaged, replace it with a new one. Are the connected components (AV receiver or amplifier, etc.) Read the operating instructions of the connected components properly set? and check the volume, input, speaker settings, etc. Is Output Terminal properly set? When ANALOG AUDIO is selected at Output Terminal, no audio signals are output from the HDMI OUT or DIGITAL OUT terminals (page 44). Is the output video resolution properly set? Use OUTPUT RESOLUTION to switch to the resolution at which the video and audio signals are output (page 25). Is the AV receiver or amplifier, etc., connected to the AUDIO To listen to 2-channel analog audio, connect to FRONT (L/R) of OUT (7.1 ch) terminals? the AUDIO OUT (7.1 ch) terminals (page 14) and set Audio Output Mode to 2 Channel (page 45). Are the speakers properly set? When the AV receiver or amplifier, etc., is connected to the AUDIO OUT (7.1 ch) terminals and Audio Output Mode is set to Multi-channel, set Speaker Setup properly (page 47). Is Pure Audio set to Mode 1 or Mode 2? If set to Mode 1 or Mode 2, signals are only output from the output terminal set at Output Terminal (page 53). Is a DVI device connected? The sound will not be output from the HDMI OUT terminals if a DVI device is connected. Connect the device to a DIGITAL OUT terminals or the AUDIO OUT (7.1 ch) terminals (page 18). Are you playing a DTS-CD? To output the sound of DTS-CDs from the HDMI OUT (SUB) terminal, set HDMI Audio Out to PCM (page 45). For some BDs, audio signals are only output from DIGITAL OUT terminals or the HDMI OUT terminals. Multi-channel sound is not Is Output Terminal properly set? output. Linear PCM (2-channel) audio signals are output from output terminals other than the one set at Output Terminal under Audio Out. Set Output Terminal properly (page 44). Is the AV receiver or amplifier connected to the HDMI OUT (SUB) terminal? The HDMI OUT (SUB) terminal outputs linear PCM 2-channel audio signals. Be sure to connect the AV receiver or amplifier to the HDMI OUT (MAIN) terminal. Is the audio output of the connected AV receiver or amplifier, Read the operating instructions of the connected AV receiver etc., properly set? or amplifier and check the audio output settings of AV receiver or amplifier. Is multi-channel sound selected? Use the menu screen or AUDIO to switch the disc's sound to multi-channel. Is the AV receiver or amplifier, etc., connected to the AUDIO OUT (7.1 ch) terminals? When the AV receiver or amplifier, etc., is connected to the AUDIO OUT (7.1 ch) terminals, set Audio Output Mode to Multi-channel (page 45). Also, set Speaker Setup properly (page 47). Noise can be heard when outputting DTS Digital Surround signals from the DIGITAL OUT terminals. Is the connected AV receiver or amplifier compatible with DTS If an AV receiver or amplifier that is not compatible with DTS Digital Surround? Digital Surround is connected to the DIGITAL OUT terminals, set DTS Out to DTS  PCM (page 44). 192 kHz or 96 kHz digital audio signals cannot be output from the DIGITAL OUT terminals. It is not possible to output 192 kHz or 96 kHz digital audio signals from this player's DIGITAL OUT terminals. The signals are automatically converted to 48 kHz or less for output. Secondary audio or interactive audio is not output. Is HDMI Audio Out properly set? Are Dolby Digital Out and DTS Out properly set? When listening to the sound from an HDMI OUT (MAIN) terminal, set HDMI Audio Out to PCM (page 45). When listening to the sound from an DIGITAL OUT terminal, set Dolby Digital Out to Dolby Digital 1, DTS Out to DTS 1 (page 44). 67 En