ProForm 325 Cse Elliptical Uk Manual - Page 8

Tip: To prevent the Wire Harness 73

Get ProForm 325 Cse Elliptical PDF manuals and user guides View all ProForm 325 Cse Elliptical manuals
Add to My Manuals
Save this manual to your list of manuals

Page 8 highlights

5. See the inset drawing. Locate the wire tie (C) in the lower end of the Upright (2). Tie the wire 5 tie to the Wire Harness (73). Next, pull the upper end of the wire tie until the Wire Harness is routed through the Upright. Tip: To prevent the Wire Harness (73) from falling into the Upright (2), secure the Wire Harness with the wire tie (C). Next, slide the Top Shield (41) downward to the Frame (1); do not press the Top Shield into place yet. Then, attach the Water Bottle Holder (29) to the Upright (2) with two M4 x 16mm Screws (52). 29 52 2 41 2 C 1 73 6. Identify the Left and Right Handlebars (85, 86). 6 Tip: Avoid pinching the Pulse Wires (84). Attach the Left and Right Handlebars (85, 86) to the Upright (2) with an M8 x 77mm Bolt (79) and an M8 Jam Nut (38); do not tighten the Bolt yet. Make sure that the M8 x 77mm Bolt (79) is inserted through the bottom hole in the Left and Right Handlebars (85, 86) and the Upright (2). Next, locate the wire ties (B) inside the Upright (2). Tie the lower ends of the wire ties to the Pulse Wires (84). Then, pull the upper ends of the wire ties until the Pulse Wires are routed through the Upright. 85 84 38 2 B 84 86 79 Avoid pinching the Pulse Wires (84) 8

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
8
5
5.
See the inset drawing.
Locate the wire tie (C)
in the lower end of the Upright (2). Tie the wire
tie to the Wire Harness (73). Next, pull the upper
end of the wire tie until the Wire Harness is
routed through the Upright.
Tip: To prevent the Wire Harness (73) from
falling into the Upright (2), secure the Wire
Harness with the wire tie (C).
Next, slide the Top Shield (41) downward to the
Frame (1);
do not press the Top Shield into
place yet.
Then, attach the Water Bottle Holder (29) to the
Upright (2) with two M4 x 16mm Screws (52).
2
29
52
6.
Identify the Left and Right Handlebars (85, 86).
Tip: Avoid pinching the Pulse Wires (84).
Attach the Left and Right Handlebars (85, 86) to
the Upright (2) with an M8 x 77mm Bolt (79) and
an M8 Jam Nut (38);
do not tighten the Bolt
yet.
Make sure that the M8 x 77mm Bolt (79)
is inserted through the bottom hole in the
Left and Right Handlebars (85, 86) and the
Upright (2).
Next, locate the wire ties (B) inside the Upright
(2). Tie the lower ends of the wire ties to the
Pulse Wires (84). Then, pull the upper ends of
the wire ties until the Pulse Wires are routed
through the Upright.
6
85
38
86
79
84
84
B
2
Avoid pinching the
Pulse Wires (84)
2
1
73
C
41