Sanyo DP42841 Owners Manual - Page 5

Getting Started - remote

Page 5 highlights

STAND ASSEMBLY ___________ NOTE: Skip these steps if you are wall mounting the TV. 1 Place HDTV face down on a padded or cushioned flat surface to protect the screen and finish. 2 Carefully insert the stand base to the bottom of the HDTV and secure the base by inserting 4 screws as indicated in the diagram below. NOTE: Stand base screws are located in the literature package. 3 Position the HDTV on a firm and flat surface with adequate space for proper ventilation. WALL MOUNTING (OPTIONAL) Wall mounting of the HDTV must be performed by a skilled person. If stand base disassembly is required: 1 Place HDTV face down on a padded or cushioned flat surface to protect the screen and finish. 2 Remove the four (4) screws securing the foot stand. CAUTION: Hold the stand firmly as you remove the last screw. Use the screws you would use to attach the stand base to secure the HDTV to a wall mounting kit. NOTE: Wall mounting kit is not included. VESA standard interface: 400 x 400 Mounting screws measurements: M6 (6mm) Diameter, Length-12mm (maximum) GETTING STARTED BATTERY INSTALLATION Install two (2) "AAA" batteries in the remote control. (Not included) To ensure safe operation, please observe the following precautions: • Replace both batteries at the same time. Do not use a new battery with a used battery. • There's a risk of explosion if a battery is replaced by an incorrect type. • Do not expose the Remote Control unit to moisture or heat. • Be sure to match the "+" and "-" signs on the batteries with marks inside the remote control. • Please properly dispose of used up batteries. ANTENNA CONNECTION FOR OFF-AIR SIGNALS OR CABLE Hook up your antenna or your cable service to the HDTV's ANT terminal with the use of a 75 OHM coaxial cable. NOTE: Keep your indoor antenna at least 3 ft. away from the television set and any other electronic equipment. ANTENNA CABLE ANALOG / DIGITAL ANTENNA IN Wall Mounting Inserts The tuner in this HDTV can receive: • Digital and Analog off air signals from an antenna • Analog or ClearQAM cable channels from a direct Cable TV connection. Need help? www.sanyoctv.com 1-800-877-5032 5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44

5
Need help?
www.sanyoctv.com
1-800-877-5032
Hook up your antenna or your cable service to the
HDTV’s
ANT
terminal with the use of a 75 OHM
coaxial cable.
NOTE: Keep your indoor antenna at least 3 ft. away
from the television set and any other electronic
equipment.
The tuner in this HDTV can receive
:
Digital and Analog off air signals from an antenna
Analog or ClearQAM cable channels from a direct
Cable TV connection.
GETTING STARTED
Install two (2) “AAA” batteries in the remote control.
(Not included)
To ensure safe operation, please observe
the following precautions:
• Replace both batteries at the same time. Do not use
a new battery with a used battery.
• There’s a risk of explosion if a battery is replaced by
an incorrect type.
• Do not expose the Remote Control unit to moisture
or heat.
• Be sure to match the
“+”
and
“–”
signs on the
batteries with marks inside the remote control.
• Please properly dispose of used up batteries.
ANTENNA CONNECTION FOR
OFF-AIR SIGNALS OR CABLE
ANTENNA
CABLE
ANALOG / DIGITAL
ANTENNA IN
BATTERY INSTALLATION
Wall mounting of the HDTV must be performed
by a skilled person.
If stand base disassembly is required:
1
Place HDTV face down
on a padded or cushioned
flat surface to protect the screen and finish.
2
Remove the four (4) screws securing the foot stand.
CAUTION:
Hold the stand firmly as you remove the
last screw.
Use the screws you would use to attach the stand base
to secure the HDTV to a wall mounting kit.
NOTE: Wall mounting kit is not included.
VESA standard interface:
400 x 400
Mounting screws measurements:
M6 (6mm) Diameter, Length—12mm (maximum)
WALL MOUNTING
(OPTIONAL)
Wall Mounting
Inserts
NOTE: Skip these steps if you are wall mounting the TV.
1
Place HDTV face down
on a padded or cushioned
flat surface to protect the screen and finish.
2
Carefully insert the stand base to the bottom of the
HDTV and secure the base by inserting 4 screws as
indicated in the diagram below.
NOTE: Stand base screws are located in the literature
package.
3
Position the HDTV on a firm and flat surface with
adequate space for proper ventilation.
STAND ASSEMBLY ___________