Sanyo PDG-DWL2500 Owners Manual - Page 74

Indicators and Projector Condition, Projector Condition

Get Sanyo PDG-DWL2500 - 2500 Lumens PDF manuals and user guides
UPC - 086483079061
View all Sanyo PDG-DWL2500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 74 highlights

Appendix Indicators and Projector Condition Check the indicators for projector condition. Indicators POWER WARNING LAMP TEMP. REPLACE 3D Red/Green Red Yellow Blue Projector Condition The projector is off. (The AC power cord is unplugged.) Normal Condition red green red green green red red green The projector is in stand-by mode. Press the ON/ ] v STAND-BY button to turn on the projector. The projector is operating normally. ] v The projector is preparing for stand-by or the ] v projection lamp is being cooled down. The projector can not be turned on until cooling is completed and the POWER indicator stops blinking. The projector is in the Power management mode. ] v The projector is in 3D display mode. ] The temperature inside the projector is abnormally high. The projector can not be turned on. When the ] v projector is cooled down enough and the temperature returns to normal, the POWER indicator stops blinking and the projector can be turned on. (The WARNING TEMP. indicator keeps blinking.) The projector has been cooled down enough and ] v the temperature returns to normal. When turning on the projector, the WARNING TEMP. indicator stops blinking. The projector detects an abnormal condition and can not be turned on. Unplug the AC power cord and plug it again to turn on the projector. If the projector ] v is turned off again, unplug the AC power cord and contact the dealer or the service center for service and checkup. Do not leave the projector on. It may cause an electric shock or a fire hazard. The lamp has been used overtime. Replace the lamp v immediately and then reset the lamp counter. The indicator will be turned off after resetting the counter. Abnormal Condition • • • on. • • • blinking. ] / v Differs according to conditions. 74 • • • off

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
²±
Check the indicators for projector condition.
• • • on.
]
/
v
• • • Differs according to conditions.
• • • blinking.
Indicators and Projector Condition
Appendix
Indicators
POWER
WARNING
TEMP°
LAMP
REPLACE
3D
Projector Condition
Red/Green
Red
Yellow
Blue
Normal Condition
The projector is off. (The AC power cord is
unplugged.)
]
v
The projector is in stand-by mode. Press the ON/
STAND-BY button to turn on the projector.
]
v
The projector is operating normally.
]
v
The projector is preparing for stand-by or the
projection lamp is being cooled down. The projector
can not be turned on until cooling is completed and
the POWER indicator stops blinking.
]
v
The projector is in the Power management mode.
]
The projector is in 3D display mode.
Abnormal Condition
]
v
The temperature inside the projector is abnormally
high. The projector can not be turned on. When the
projector is cooled down enough and the temperature
returns to normal, the POWER indicator stops
blinking and the projector can be turned on. (The
WARNING TEMP. indicator keeps blinking.)
]
v
The projector has been cooled down enough and
the temperature returns to normal. When turning on
the projector, the WARNING TEMP. indicator stops
blinking.
]
v
The projector detects an abnormal condition and can
not be turned on. Unplug the AC power cord and
plug it again to turn on the projector. If the projector
is turned off again, unplug the AC power cord and
contact the dealer or the service center for service
and checkup. Do not leave the projector on. It may
cause an electric shock or a fire hazard.
v
The lamp has been used overtime. Replace the lamp
immediately and then reset the lamp counter. The
indicator will be turned off after resetting the counter.
red
green
red
green
red
red
green
green
• • • off