Sanyo PLC-XU355 Instruction Manual, PLC-XU355

Sanyo PLC-XU355 - XGA LCD Projector Manual

Sanyo PLC-XU355 manual content summary:

  • Sanyo PLC-XU355 | Instruction Manual, PLC-XU355 - Page 1
    Multimedia Projector MODEL PLC-XU305 PLC-XU355 PLC-XU305K PLC-XU355K Network Supported □ Wireless LAN IEEE802.11b/g □ Wired LAN 100-Base-TX/10-Base-T Memory Viewer □ USB Memory Viewer * Refer to the owner's manuals below for details about network and memory viewer function. ■ Network Set
  • Sanyo PLC-XU355 | Instruction Manual, PLC-XU355 - Page 2
    well as operate and manage the projector via network. For details, refer to the owner's manual ♦ Power Management "Network Set-up and Operation." The Power management function reduces power ♦ Memory Viewer Function consumption and maintains the lamp life (p.53). Insert the dedicated USB memory
  • Sanyo PLC-XU355 | Instruction Manual, PLC-XU355 - Page 3
    Cap 63 Cleaning the Projection Lens 63 Cleaning the Projector Cabinet 63 Lamp Replacement 64 Appendix 66 Troubleshooting 66 Menu Tree 70 Indicators and Projector Condition 72 Compatible Computer Specifications 73 Technical Specifications 75 Optional Parts 76 PJ Link Notice 77
  • Sanyo PLC-XU355 | Instruction Manual, PLC-XU355 - Page 4
    problem still persists, contact the dealer where you purchased the projector or the service center. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE EXCEPT LAMP REPLACEMENT. REFER SERVICING
  • Sanyo PLC-XU355 | Instruction Manual, PLC-XU355 - Page 5
    with the projector. Wall or shelf mounting should follow the manufacturer's instructions, and should use a mounting kit projector exhibits a distinct change in performance-this indicates a need for service. When replacement parts are required, be sure the service technician has used replacement
  • Sanyo PLC-XU355 | Instruction Manual, PLC-XU355 - Page 6
    ' running speed is changed according to the temperature inside the projector. Installing the Projector in Proper Position Install the projector properly. Improper Installation may reduce the lamp life and cause a fire hazard. Do not tilt the projector more than 20 degrees from side to side. 30
  • Sanyo PLC-XU355 | Instruction Manual, PLC-XU355 - Page 7
    unless otherwise specified in the instructions. If such changes or modifications should be made, you could be required to stop operation of the equipment. Model Number PLC-XU305, PLC-XU355 Trade Name Sanyo Responsible party : SANYO FISHER COMPANY Address 21605 Plummer Street
  • Sanyo PLC-XU355 | Instruction Manual, PLC-XU355 - Page 8
    Remote Receiver ② Zoom Ring ③ Focus Ring ④ Projection Lens ⑤ Lens Cap (See page 63 for attaching.) CAUTION Do not turn on a projector with Connector (Series A) are for the Network function. Refer to the owner's manual "Network Set-up and Operation" .  Kensington Security Slot This slot is
  • Sanyo PLC-XU355 | Instruction Manual, PLC-XU355 - Page 9
    ⑥ ① CONTROL PORT When the projector is controlled by a computer, connect Digital/Analog DVI-I type) to this terminal (p.16). ⑤ LAN Connection Terminal Connect the LAN cable (refer to the owner's manual computer with the remote control and use the PAGE ▲▼buttons on the remote control during a
  • Sanyo PLC-XU355 | Instruction Manual, PLC-XU355 - Page 10
    On-Screen Menu (p.23). -Pan the image in the Digital zoom + mode (p.38). -Adjust the volume level ( projector exceeds the operating range (pp.61, 72). ⑨ LAMP REPLACE indicator Lights yellow when the projection lamp reaches its end of life (pp.64, 72). ⑩ WIRELESS indicator Turn green when the wireless
  • Sanyo PLC-XU355 | Instruction Manual, PLC-XU355 - Page 11
    LAMP button Select a lamp mode. (pp.27, 55) ⑮ D .ZOOM ▲▼ buttons Zoom in and out the images. (pp.27, 38) ⑯ RESET/ON/ALL-OFF switch When using the remote the image in Digital zoom mode. (p.38) ㉔ PRESENTATION POINTER button Move a pointer of the projector or a pointer for wireless mouse operation.
  • Sanyo PLC-XU355 | Instruction Manual, PLC-XU355 - Page 12
    to activate the Pointer function. (The Laser pointer has switched to the Pointer function.)  Press the LASER button on the remote control pointing toward the projector. The Spotlight or Pointer is displayed on the screen with the LASER button lighting green. Then move the Spotlight or Pointer with
  • Sanyo PLC-XU355 | Instruction Manual, PLC-XU355 - Page 13
    Mouse Operation The remote control can be used as a wireless mouse for your computer. 1 Before operating the wireless mouse, connect your computer and the projector with a USB cable (not supplied). See "Connecting to a Computer" on page 16. When the Pointer function is used, the wireless mouse is
  • Sanyo PLC-XU355 | Instruction Manual, PLC-XU355 - Page 14
    an explosion if battery is replaced by an incorrect type. ● Dispose of used batteries according to the instructions or your local disposal rule or guidelines. Remote Control Operating Range Point the remote control toward the projector (Infrared Remote Receiver) when pressing the buttons. Maximum
  • Sanyo PLC-XU355 | Instruction Manual, PLC-XU355 - Page 15
    Installation Positioning the Projector For projector positioning, see the figures below. The projector should be set perpendicularly to the plane of the screen. Note: • The brightness in the room has a great influence on picture quality. It is recommended
  • Sanyo PLC-XU355 | Instruction Manual, PLC-XU355 - Page 16
    IN 1/ COMPONENT IN terminal as input. • When the AUDIO OUT is plugged-in, the projector's built-in speaker is not available. • USB cable connection is needed when operating the computer with the remote control or using the PAGE ▲▼ buttons on the remote control. 16 Unplug the power cords of both the
  • Sanyo PLC-XU355 | Instruction Manual, PLC-XU355 - Page 17
    cable Audio cable (stereo) S-Video cable AUDIO IN VIDEO AUDIO OUT (stereo) S-VIDEO Note: • When the AUDIO OUT is plugged-in, the projector's builtin speaker is not available. • The S-VIDEO jack connection overrides the VIDEO jack connection when selecting Auto in the Input Menu (p.41
  • Sanyo PLC-XU355 | Instruction Manual, PLC-XU355 - Page 18
    used for connection • Audio Cables • Scart-VGA Cable • VGA Cable • Component Cable • Component-VGA Cable (Cables are not supplied with this projector.) RGB Scart 21pin Output Component Video Output (Y, Pb/Cb, Pr/Cr) Monitor Input Audio Output Component cable Scart-VGA cable ComponentVGA
  • Sanyo PLC-XU355 | Instruction Manual, PLC-XU355 - Page 19
    system. If you are not sure of the type of power being supplied, consult your authorized dealer or service station. Connect the projector with all peripheral equipment before turning the projector on. CAUTION The AC outlet must be near this equipment and must be easily accessible. Note: Unplug
  • Sanyo PLC-XU355 | Instruction Manual, PLC-XU355 - Page 20
    after 30 seconds. Selected Input Source and Lamp Control Video Lamp control status (See page 55 for Lamp control status.) Note: The Filter warning and Lamp replacement icons may appear on the screen depending on the usage state of the projector. Video / PC selection window Cancel Input signal
  • Sanyo PLC-XU355 | Instruction Manual, PLC-XU355 - Page 21
    projector. Setting a PIN code prevents unauthorized use of the projector. A PIN code consists of a four-digit projector. Note: • If the PIN code number is not entered within three minutes after the PIN code dialog box appeared, the projector your PIN code, the projector can no longer be started.
  • Sanyo PLC-XU355 | Instruction Manual, PLC-XU355 - Page 22
    on the remote control, and Power off? appears on the screen. 2 Press the ON/STAND-BY button again to turn off the projector. The OFF. DO NOT OPERATE THE PROJECTOR CONTINUOUSLY WITHOUT REST. CONTINUOUS USE MAY RESULT IN SHORTENING THE LAMP LIFE. TURN OFF THE PROJECTOR AND LET STAND FOR ABOUT AN
  • Sanyo PLC-XU355 | Instruction Manual, PLC-XU355 - Page 23
    , which are further divided into other submenus. For each adjustment and setting procedure, refer to respective sections in this manual. 1 Press the MENU button on the top control or the remote control to display the On-Screen Menu.  Use the Point ▲▼ buttons to highlight or select a main menu item
  • Sanyo PLC-XU355 | Instruction Manual, PLC-XU355 - Page 24
    and Digital zoom projector's operating configurations (pp.46-59).  Information Display the input source information: Input , H-sync freq., V-sync freq., Screen, Language, Lamp status, Lamp counter, Power management, Key lock, PIN code lock and Remote control (p.60).  Network See owner's manual
  • Sanyo PLC-XU355 | Instruction Manual, PLC-XU355 - Page 25
    it does not correct horizontal distortion. • Auto Keystone cannot work when Ceiling feature is set to On in the Setting menu (p.52). • Perfect SETUP/CANCEL or AUTO SET/CANCEL button, adjust manually by pressing the KEYSTONE button on the remote control or selecting Keystone in the Setting menu (p.
  • Sanyo PLC-XU355 | Instruction Manual, PLC-XU355 - Page 26
    on, press the MUTE button again to select Off or press the VOLUME +/- buttons. The Mute function is also effective for the AUDIO OUT jack. Remote Control VOLUME+/buttons VOL- button VOL+ button Menu Operation 1 Press the MENU button to display the On-Screen Menu. Use the Point ▲▼ buttons to
  • Sanyo PLC-XU355 | Instruction Manual, PLC-XU355 - Page 27
    , PIN code lock and Remote control (p.60). D.ZOOM buttons LAMP button D.ZOOM buttons Press the D.ZOOM buttons on the remote control to enter to the Digital zoom +/- mode. See page 38 for details. LAMP button Press the LAMP button on the remote control to select the lamp mode for changing the
  • Sanyo PLC-XU355 | Instruction Manual, PLC-XU355 - Page 28
    Basic Operation NO SHOw button Press the NO SHOW button on the remote control to black out the image. To restore to normal, press the NO SHOW button again or press any other button. When a projected image is captured and set as User in the Logo selection (see page 49), the screen changes
  • Sanyo PLC-XU355 | Instruction Manual, PLC-XU355 - Page 29
    should be selected through Menu operation as described below. Remote Control COMPUTER button Computer 1 Top Control INPUT button button. Input Menu Note: • Network is for the Network function. See owner's manual "Network Set-up and Operation". • When the Input Search function is set to On1
  • Sanyo PLC-XU355 | Instruction Manual, PLC-XU355 - Page 30
    through Menu operation as described below. Remote Control Top Control INPUT button COMPUTER button Digital Content Protection, LLC. Should the specification be changed, this projector may not display the digital content protected by HDCP. • Network is for the Network function. See owner's manual
  • Sanyo PLC-XU355 | Instruction Manual, PLC-XU355 - Page 31
    XGA, SXGA, WXGA, or UXGA with its Multi-scan system and Auto PC Adjustment. If a computer is selected as a signal source, this projector Check the connection between your computer and the projector. (See "Troubleshooting" on page 66.) The preset system is manually adjusted in the PC Adjust Menu. The
  • Sanyo PLC-XU355 | Instruction Manual, PLC-XU355 - Page 32
    adjusted parameters from the Auto PC Adjustment can be stored in the projector. Once the parameters are stored, the setting can be done just by Adjustment function. When the image is not provided properly with this operation, manual adjustments are required (pp.33-34). • The Auto PC Adjustment
  • Sanyo PLC-XU355 | Instruction Manual, PLC-XU355 - Page 33
    enables you to precisely adjust several parameters to match those signal formats. The projector has five independent memory areas to store those parameters manually adjusted. It allows you to recall the setting for a specific computer. 1 Press the MENU button to display the On-Screen Menu. Use the
  • Sanyo PLC-XU355 | Instruction Manual, PLC-XU355 - Page 34
    480i, 575i, 480p, 575p, 720p, 1035i or 1080i is selected in the PC System Menu (p.31). • PC Adjust Menu cannot be selected when Computer 2(PC digital) is selected in the Input Menu (p.30). 34
  • Sanyo PLC-XU355 | Instruction Manual, PLC-XU355 - Page 35
    by pressing the IMAGE button on the remote control. Remote Control IMAGE button Menu Operation 1 Press Standard Normal picture mode preset on the projector. Real Picture mode with improved halftone for four colors. Image 1-4 For viewing with the user preset image mode in the Image Adjust Menu
  • Sanyo PLC-XU355 | Instruction Manual, PLC-XU355 - Page 36
    mode Use the Point ◄► buttons to adjust the setting value. Note: • When White balance Red, Green or Blue is adjusted, Color temp. will change to User. • When Blackboard(Green) or Colorboard is selected in Image select, Color temp. will change to Blackboard or Colorboard. 36
  • Sanyo PLC-XU355 | Instruction Manual, PLC-XU355 - Page 37
    resolution is higher than it, reset the resolution to the lower before connecting to the projector. • The image data in other than 1024 x 768 is modified to fit the screen size in initial mode. • True, Full and Digital zoom +/- cannot be selected when 480i, 575i, 480p or 575p is selected in the
  • Sanyo PLC-XU355 | Instruction Manual, PLC-XU355 - Page 38
    Input Custom Adjust the screen scale and position manually with this function. Press the SELECT button A projected image can be also expanded by pressing the D.ZOOM ▲ button on the remote control. Digital zoom - Select Digital zoom -. The On-Screen Menu disappears and D . zoom - appears. Press the
  • Sanyo PLC-XU355 | Instruction Manual, PLC-XU355 - Page 39
    button on the top control or the VIDEO button on the remote control. Before using these buttons, correct input source should be selected S-video. Video Note: • Network is for the Network function. See the owner's manual "Network Set-up and Operation" . • When the Input Search function is set to
  • Sanyo PLC-XU355 | Instruction Manual, PLC-XU355 - Page 40
    should be selected through Menu operation as described below. Remote Control Top Control INPUT button COMPUTER button Computer 1 Computer RGB (Scart). Note: • Network is for the Network function. See owner's manual "Network Set-up and Operation" . • When the Input Search function is set
  • Sanyo PLC-XU355 | Instruction Manual, PLC-XU355 - Page 41
    itself to optimize its performance. When Video System is PAL-M or PAL-N, select the system manually. PAL/SECAM/NTSC/NTSC4.43/PAL-M/PAL-N If the projector cannot reproduce proper video image, select a specific broadcast signal format from among PAL, SECAM, NTSC, NTSC 4.43, PAL-M and PAL-N. Component
  • Sanyo PLC-XU355 | Instruction Manual, PLC-XU355 - Page 42
    button . Remote Control IMAGE button Dynamic For viewing pictures in a bright room. Standard Normal picture mode preset on the projector. Cinema Picture the wall color from the preset four colors. Image 1-4 For viewing with the user preset image mode in the Image Adjust Menu (see pages 43-44). This
  • Sanyo PLC-XU355 | Instruction Manual, PLC-XU355 - Page 43
    the Point ◄► buttons to adjust the setting value. Note: • When White balance Red, Green or Blue is adjusted, the Color temp. level will change to User. • Tint cannot be selected when the video system is PAL, SECAM, PAL-M or PAL-N (p.41). • When Blackboard(Green) or Colorboard is selected in Image
  • Sanyo PLC-XU355 | Instruction Manual, PLC-XU355 - Page 44
    options. Off.......... Disabled. L1........... For an active picture. L2........... For a still picture. Film........ For watching a film. With this function, the projector reproduces pictures faithful to the original film quality. Reset To reset the adjusted data, select Reset and press the SELECT
  • Sanyo PLC-XU355 | Instruction Manual, PLC-XU355 - Page 45
    Video Input Screen Size Adjustment This projector has the picture screen resize function, which Provide the image at the 16:9 wide screen ratio. Custom Adjust the screen scale and position manually with this function. Press the SELECT button at Custom and Custom is displayed on the screen for
  • Sanyo PLC-XU355 | Instruction Manual, PLC-XU355 - Page 46
    Setting Setting This projector has a Setting menu that allows you to set up the other various functions described below. 1 Press the MENU button to display the On-Screen Menu.
  • Sanyo PLC-XU355 | Instruction Manual, PLC-XU355 - Page 47
    remote control or the AUTO SETUP/CANCEL button on the top control. Off Disables Auto PC Adjustment. Auto Keystone Auto Always works and corrects keystone distortion according to the projector's tilt. Manual Auto Keystone function cannot work when the Ceiling feature is set On in the Setting menu
  • Sanyo PLC-XU355 | Instruction Manual, PLC-XU355 - Page 48
    the Logo setting (see page 49) is set to Off with the User background, the Background setting will be switched to Blue. Keystone Display This countdown when turning on the projector. Use this function when you want to project the image as early as possible even when the lamp is not bright enough.
  • Sanyo PLC-XU355 | Instruction Manual, PLC-XU355 - Page 49
    , capture and Logo PIN code change cannot be selected. Logo select Logo select This function decides on the starting-up display from among following options. User......... Show the image you captured Default..... Show the factory-set logo Off Show the countdown display only Setting 49
  • Sanyo PLC-XU355 | Instruction Manual, PLC-XU355 - Page 50
    select function and set it to User. Then the captured image will be displayed the next time you turn on the projector or when you press the NO image (pp.35, 42). • A signal from a computer can be captured up to XGA (1024 x 768). A signal from video equipment can be captured except for 720p, 1035i
  • Sanyo PLC-XU355 | Instruction Manual, PLC-XU355 - Page 51
    a four-digit number. After entering the four-digit number, move the pointer to Set. Press the SELECT button so that you can start to operate the projector. If PIN code change Logo PIN code can be changed to your desired four-digit number. Press the Point ▼ button to select Logo PIN code change and
  • Sanyo PLC-XU355 | Instruction Manual, PLC-XU355 - Page 52
    this function is set to On, the picture will be top/ bottom and left/right reversed. This function is used to project the image from a ceiling-mounted projector. Rear When this function is set to On, the picture will be left/right reversed. This function is used to project the image from rear
  • Sanyo PLC-XU355 | Instruction Manual, PLC-XU355 - Page 53
    lamp life, the Power management function turns off the projection lamp when the projector is not operated for a certain period. Select one of the following options: Ready When the lamp on the top control or remote control is pressed. Shut down........... When the lamp has been fully cooled down,
  • Sanyo PLC-XU355 | Instruction Manual, PLC-XU355 - Page 54
    is powered off. Eco Select Eco when you do not use the projector via network. The projector's network function will stop when turning off the projector. Refer to the owner's manual "Network Set-up and Operation". Note: • Factory default is Eco. • When selecting Normal, the cooling fans may
  • Sanyo PLC-XU355 | Instruction Manual, PLC-XU355 - Page 55
    on. Then the projector will turn off after 3 minutes. Lamp replacement icon Lamp life control • The Lamp replacement icon will not appear when the Display function is set to Off (p.48), during "Freeze" (p.27), or "No show" (p.28). Remote control The eight different remote control codes (Code
  • Sanyo PLC-XU355 | Instruction Manual, PLC-XU355 - Page 56
    becomes locked and you do not have the remote control nearby or there is something wrong with your remote control, contact the dealer where you purchased the projector or the service center. PIN code lock This function prevents the projector from being operated by unauthorized persons and provides
  • Sanyo PLC-XU355 | Instruction Manual, PLC-XU355 - Page 57
    , and then enter the correct number. Repeat this step to complete entering a four-digit number. After entering the four-digit number, move the pointer to Set. Press the SELECT button so that you can start to operate the projector. If you entered an incorrect PIN code, PIN code and the number will
  • Sanyo PLC-XU355 | Instruction Manual, PLC-XU355 - Page 58
    turned off (p.22). L1....... Normal operation L2....... Slower and lower-sound than the normal operation (L1), but it takes more time to cool the projector down. Fan control Choose the running speed of cooling fans from the following options according to the ground elevation under which you use the
  • Sanyo PLC-XU355 | Instruction Manual, PLC-XU355 - Page 59
    log This function records anomalous operations while the projector is in operation and use it when diagnosing default This function returns all setting values except for the User logo, PIN code lock, Logo PIN code lock, Lamp counter and Filter counter to the factory default settings. Factory
  • Sanyo PLC-XU355 | Instruction Manual, PLC-XU355 - Page 60
    of the projector. Direct Operation Press the INFO. button on the remote control to display the Information Menu. Remote Control Menu Operation selected language is displayed. Lamp status The selected lamp mode is displayed. Lamp counter The cumulative lamp operating time is displayed. Power
  • Sanyo PLC-XU355 | Instruction Manual, PLC-XU355 - Page 61
    cannot be turned on and the WARNING indicator still lights red, unplug the AC power cord and contact the service station. CAUTION DO NOT LEAVE THE PROJECTOR WITH THE AC POWER CORD CONNECTED UNDER AN ABNORMAL CONDITION. IT MAY RESULT IN FIRE OR ELECTRIC SHOCK. Top Control WARNING emit a red
  • Sanyo PLC-XU355 | Instruction Manual, PLC-XU355 - Page 62
    , LCD panels, or optical elements inside the projector degrading the quality of a projected image. When the symptoms above are noticed, contact your authorized dealer or service station for proper cleaning. Resetting the Filter Counter Be sure to reset the Filter counter after cleaning or replacing
  • Sanyo PLC-XU355 | Instruction Manual, PLC-XU355 - Page 63
    Attaching the Lens Cap When moving the projector or while it is not in use, replace the lens cap. 1 Thread the string through the hole on the lens cap and then tie a knot in the string to secure it in place. 2
  • Sanyo PLC-XU355 | Instruction Manual, PLC-XU355 - Page 64
    not drop a lamp or touch a glass bulb! The glass can shatter and may cause injury. CAUTION When replacing the lamp because it has stopped illuminating, there is a possibility that the lamp may be broken. If replacing the lamp of a projector which has been installed on the ceiling, you should always
  • Sanyo PLC-XU355 | Instruction Manual, PLC-XU355 - Page 65
    to the dealer. ● Model No. of your projector ● Replacement Lamp Type No. : PLC-XU305, PLC-XU355 PLC-XU305K, PLC-XU355K : POA-LMP131 (Service Parts No. 610 343 2069) LAMP HANDLING PRECAUTIONS This projector uses a high-pressure lamp which must be handled carefully and properly
  • Sanyo PLC-XU355 | Instruction Manual, PLC-XU355 - Page 66
    the Ceiling function. See page 52. - Check if the Contrast or Brightness are adjusted properly. See pages 36,43. - Check if Image mode is selected properly. See pages 35,42. - Check the lamp control function. See pages 27,55. - Check the LAMP REPLACE indicator. If it lights, the end of lamp life is
  • Sanyo PLC-XU355 | Instruction Manual, PLC-XU355 - Page 67
    connecting to a projector. See your computer's instruction manual for the setting. NO SHOW button or any other button on the remote control. No sound - Check the audio cable digital signal is input into DVI terminal. See page 32 - The icon is not available in grayout when the digital
  • Sanyo PLC-XU355 | Instruction Manual, PLC-XU355 - Page 68
    remote control can not be used as a wireless mouse. - Make sure the signal is from the computer, otherwise, the remote control can not be used as a wireless mouse. - Turn on the projector you purchased the projector or the service lock, Security key lock or Security center. PIN code lock. 68
  • Sanyo PLC-XU355 | Instruction Manual, PLC-XU355 - Page 69
    Appendix WARNING : High voltages are used to operate this projector. Do not attempt to open the cabinet. If problems still persist after following all operating instructions, contact the dealer where you purchased the projector or the service center. Specify the model number and explain about the
  • Sanyo PLC-XU355 | Instruction Manual, PLC-XU355 - Page 70
    Computer 2 Video S-video Network RGB Component RGB (Scart) RGB (PC digital) RGB(AV HDCP) RGB (Analog) Sound Sound Volume Mute 0-63 On /Yellow/Green Contrast Brightness Color temp. 0-63 0-63 XLow Low Mid High User Red Green Blue Sharpness Gamma Reset Store Normal True Wide Full Custom 0-63
  • Sanyo PLC-XU355 | Instruction Manual, PLC-XU355 - Page 71
    On/Off Standby mode Normal / Eco Closed Caption Lamp control Closed Caption CC1/CC2/CC3/CC4 Color Color/White Lamp control Normal Remote control Security Fan Fan control Eco Lamp life control Mode 1/Mode 2 Code 1-Code 8 Key lock Off Projector Remote control PIN code lock Off/On1/On2 PIN
  • Sanyo PLC-XU355 | Instruction Manual, PLC-XU355 - Page 72
    dealer or the service center for service and checkup. Do not leave the projector on. It may cause an electric shock or a fire hazard. • • • green • • • red • • • off • • • blinks green • • • blinks red When the projection lamp reaches its end of life, the LAMP REPLACE indicator lights yellow
  • Sanyo PLC-XU355 | Instruction Manual, PLC-XU355 - Page 73
    Appendix Compatible Computer Specifications Basically this projector can accept the signal from all computers with the V-, H-Frequency mentioned below and less than 140 MHz of Dot Clock for analog signal and 110 MHz of Dot Clock for digital signal. When selecting these modes, PC adjustment can be
  • Sanyo PLC-XU355 | Instruction Manual, PLC-XU355 - Page 74
    Appendix When the input signal is digital from DVI terminal, refer to the chart below. ON-SCREEN DISPLAY D-VGA D-480p D-575p D-SVGA D-XGA D-WXGA 1 D-WXGA 2 D-WXGA 3 D-WXGA 4 D-WXGA 5 D-WXGA 6 displayed properly depending on computers. • The specifications are subject to change without notice. 74
  • Sanyo PLC-XU355 | Instruction Manual, PLC-XU355 - Page 75
    Appendix Technical Specifications Mechanical Information Projector Type Dimensions (W x H x D) Net Weight Feet Adjustment Multi-media Projector 12.80" x 3.27" x 9.12" (326mm x 83.1mm x 231.6mm) (Not including protrusions) 2.9 kg 0˚ to 12˚ Panel Resolution LCD Panel System Panel Resolution
  • Sanyo PLC-XU355 | Instruction Manual, PLC-XU355 - Page 76
    Guide and Safety Manual AC Power Cord Remote Control and Batteries VGA Cable Lens Cap with String PIN Code Label Network Application (CD-ROM) USB thumb drive for Auto Capture Case (for USB thumb drive) Hook and Loop Fastener Soft Carrying Case Safety Instructions ● The specifications
  • Sanyo PLC-XU355 | Instruction Manual, PLC-XU355 - Page 77
    ). This projector supports all commands defined by PJLink Class 1 and is verified conformance with PJLink Standard Class 1. For PJ Link password, see page 49 on the owner's manual "Network Set-up and Operation." Projector Input Computer 2 (Analog) Computer 2 (Digital) RGB (PC digital) RGB
  • Sanyo PLC-XU355 | Instruction Manual, PLC-XU355 - Page 78
    /----10 Ground (Vert.sync.) 11 Ground/----12 DDC Data/----13 Horiz. sync. Input/Output (Composite H/V sync.) 14 Vert. sync. 15 DDC Clock/----- COMPUTER 2 / DVI-I TERMINAL (DIGITAL/ANALOG) C1 C2 12345678 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 C3 C4 C5 C1 Analog Red
  • Sanyo PLC-XU355 | Instruction Manual, PLC-XU355 - Page 79
    with this manual securely. If you forgot or lost the number and unable to operate the projector, contact the service station. PIN Code Lock No. Factory default set No: 1 2 3 4* Logo PIN Code Lock No. Factory default set No: 4 3 2 1* *Should the four-digit
  • Sanyo PLC-XU355 | Instruction Manual, PLC-XU355 - Page 80
    Appendix Dimensions 93.5(3.68) 232.5(9.15) 109.7(4.32) 144.9(5.70) 121.9(4.80) Unit: mm(inch) Screw Holes for Ceiling Mount Screw: M4 Depth: 12.0(0.472) 219.4(8.64) 101(3.98) 55(2.17) < <
  • Sanyo PLC-XU355 | Instruction Manual, PLC-XU355 - Page 81
    KG5AC SANYO Electric Co., Ltd.
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81

Multimedia Projector
MODEL
PLC-XU305
PLC-XU355
PLC-XU305K
PLC-XU355K
Owner’s Manual
Network Supported
Wireless LAN
IEEE802.11b/g
Wired LAN
100-Base-TX/10-Base-T
Memory Viewer
USB Memory Viewer
*
Refer to the owner’s manuals
below for details about network
and memory viewer function.
Network Set-up and Operation
Memory viewer