Sanyo PLC-XU355 Instruction Manual, PLC-XU355 - Page 55

Lamp control, Remote control

Get Sanyo PLC-XU355 - XGA LCD Projector PDF manuals and user guides
UPC - 086483073847
View all Sanyo PLC-XU355 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 55 highlights

Setting Lamp control Lamp control This function allows you to change brightness of the screen. Normal....... Normal brightness Eco Lower brightness reduces the lamp power consumption and extends the lamp life. Lamp life control Select the lamp operation when the total lighting time of a lamp exceeds the recommended total hours of use. Mode 1 A lamp can be turned on even after exceeding the recommended total hours of use. Mode 2 A lamp can be turned on even after exceeding the recommended total hours of use. But the projector turns off automatically after 3 minutes. Note: • Lamp mode cannot be changed for a while after turning on the projector. Lamp needs some time to stabilize after the power is turned on. Stored lamp mode will be active after the lamp is stabilized. • If Mode 2 has been selected and the projection lamp exceedes the recommended total hours of use, the replacement icon will be displayed at the time of power on. Then the projector will turn off after 3 minutes. Lamp replacement icon Lamp life control • The Lamp replacement icon will not appear when the Display function is set to Off (p.48), during "Freeze" (p.27), or "No show" (p.28). Remote control The eight different remote control codes (Code 1-Code 8) are assigned to the projector; the factory-set, initial code (Code 1) and the other seven codes (Code 2 to Code 8). The same code should set on both the projector and the remote control. For example, operating the projector in Code 7, the remote control code also must be switched to Code 7. To change the code for the projector Select a remote control code in this Setting Menu. To change the code for the remote control: While holding down the MENU button, press the IMAGE button the number of times corresponding to the remote control code for the projector. See "Remote Control Code" on page 13. Remote control Note: • When different codes are set on the projector and on the remote control, any operation cannot be made. In that case, switch the code on the remote control to fit the code on the projector. • If the batteries are removed from the remote control for a long period of time, the remote control code will be reset. 55

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
55
Remote control
This function allows you to change brightness of the
screen.
Norma
l
......
Normal brightness
Eco
............
Lower brightness reduces the lamp
power consumption and extends the
lamp life.
Lamp control
Remote control
Lamp life control
The eight different remote control codes (Code 1–Code 8)
are assigned to the projector; the factory-set, initial code
(Code 1) and the other seven codes (Code 2 to Code 8).
The same code should set on both the projector and the
remote control. For example, operating the projector in
Code 7
, the remote control code also must be switched to
Code 7
.
To change the code for the projector
Select a remote control code in this Setting Menu.
To change the code for the remote control:
While holding down the MENU button, press the IMAGE
button the number of times corresponding to the remote
control code for the projector. See “
Remote Control Code
”
on page 13.
Lamp control
Select the lamp operation when the total lighting time of a
lamp exceeds the recommended total hours of use.
Mode 1
..............
A lamp can be turned on even after
exceeding the recommended total
hours of use.
Mode ±
..............
A lamp can be turned on even after
exceeding the recommended total
hours of use. But the projector turns off
automatically after 3 minutes.
Lamp life control
Setting
Note:
•
Lamp mode cannot be changed for a while after turning
on the projector. Lamp needs some time to stabilize after
the power is turned on. Stored lamp mode will be active
after the lamp is stabilized.
• If
Mode ±
has been selected and the projection lamp
exceedes the recommended total hours of use, the
replacement icon will be displayed at the time of power-
on. Then the projector will turn off after 3 minutes.
• The Lamp replacement icon will not appear when the
Display function is set to Off (p.48), during "Freeze" (p.27),
or "No show" (p.28).
Note:
• When different codes are set on the projector and on the remote control, any operation cannot be made. In
that case, switch the code on the remote control to fit the code on the projector.
• If the batteries are removed from the remote control for a long period of time, the remote control code will
be reset.
Lamp replacement icon