Sanyo PLC-XU355 Instruction Manual, PLC-XU355 - Page 66

Appendix, Troubleshooting

Get Sanyo PLC-XU355 - XGA LCD Projector PDF manuals and user guides
UPC - 086483073847
View all Sanyo PLC-XU355 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 66 highlights

Appendix Troubleshooting Before calling your dealer or service center for assistance, check the items below once again. -Make sure you have properly connected the projector to peripheral equipment as described on pages 16-18. -Make sure all equipment is connected to AC outlet and the power is turned on. -When the projector does not project an image from the connected computer, restart the computer. Problem: - Solutions No power - Plug the power cord of the projector into the AC outlet. - See if the POWER indicator lights red. - Wait until the POWER indicator stops blinking to turn on the projector again. The projector can be turned on after the POWER indicator turns red. See page 20. - Check the WARNING indicator. If the WARNING indicator lights red, projector cannot be turned on. See page 61. - Check the projection lamp. See page 64. - Unlock the Key lock function for the projector. See page 56. The initial display is not shown. - Make sure Off or Countdown off are not chosen at display function. See page 48. The initial display is not same as the default set. - Make sure User or Off are not chosen at Logo (select) function. See page 49. Input signal switches automatically. - Make sure Input search function is adjusted properly. See page 47. (or does not switch automatically) Wh e n t h e p r o j e c t o r i s o n a n d That is the Filter warning icon. See page 58. youpress the input button, an icon other than the Lamp mode icon appears. An icon other than Input mode or Lamp mode icon appears. Image is out of focus. - That is the Lamp replacement icon or the Filter warning icon. See pages 58, 64. - Adjust focus of the projector. See page 25. - Provide proper distance between the projector and the projection screen. See page 15. - Check the projection lens to see if it needs cleaning. See page 63. - Moving the projector from a cool to warm place may result in moisture condensation on the projection lens. In such cases, leave the projector off and wait until condensation evaporates. Image is Left/Right reversed. Image is Top/Bottom reversed. Picture is not bright enough. - Check the Ceiling/Rear function. See page 52. - Check the Ceiling function. See page 52. - Check if the Contrast or Brightness are adjusted properly. See pages 36,43. - Check if Image mode is selected properly. See pages 35,42. - Check the lamp control function. See pages 27,55. - Check the LAMP REPLACE indicator. If it lights, the end of lamp life is approaching. Replace the lamp with a new one promptly. See page 64. 66

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
66
Problem:
– Solutions
– Plug the power cord of the projector into the AC outlet.
– See if the POWER indicator lights red.
– Wait until the POWER indicator stops blinking to turn on the projector
again. The projector can be turned on after the POWER indicator
turns red. See page 20.
– Check the WARNING indicator. If the WARNING indicator lights red,
projector cannot be turned on. See page 61.
– Check the projection lamp. See page 64.
– Unlock the Key lock function for the projector. See page 56.
– Make sure
Off
or
Countdown off
are not chosen at display
function. See page 48.
– Make sure
User
or
Off
are not chosen at Logo (select)
function. See page 49.
– Make sure Input search function is adjusted properly. See page 47.
– That is the Filter warning icon. See page 58.
– That is the Lamp replacement icon or the Filter warning icon. See
pages 58, 64.
– Adjust focus of the projector. See page 25.
– Provide proper distance between the projector and the projection
screen. See page 15.
– Check the projection lens to see if it needs cleaning. See page 63.
– Moving the projector from a cool to warm place may result in
moisture condensation on the projection lens. In such cases, leave
the projector off and wait until condensation evaporates.
– Check the Ceiling/Rear function. See page 52.
– Check the Ceiling function. See page 52.
– Check if the
Contrast
or
Brightness
are adjusted properly. See
pages 36,43.
– Check if
Image mode
is selected properly. See pages 35,42.
– Check the lamp control function. See pages 27,55.
– Check the LAMP REPLACE indicator. If it lights, the end of lamp life
is approaching. Replace the lamp with a new one promptly. See page
64.
Appendix
Troubleshooting
Before calling your dealer or service center for assistance, check the items below once again.
–Make sure you have properly connected the projector to peripheral equipment as described on pages 16-18.
–Make sure all equipment is connected to AC outlet and the power is turned on.
–When the projector does not project an image from the connected computer, restart the computer.
No power
The initial display is not shown°
The initial display is not same
as the default set°
Input signal switches automatically°
(or does not switch automatically)
When the projector is on and
youpress the input button, an icon
other than the Lamp mode icon
appears
.
An icon other than Input mode or
Lamp mode icon appears°
Image is out of focus°
Image is Left/Right reversed°
Image is Top/Bottom reversed°
Picture is not bright enough°