Sanyo PLV Z1 Owners Manual
Sanyo PLV Z1 - LCD Projector - 700 ANSI Lumens Manual
 |
UPC - 086483045776
View all Sanyo PLV Z1 manuals
Add to My Manuals
Save this manual to your list of manuals |
Sanyo PLV Z1 manual content summary:
- Sanyo PLV Z1 | Owners Manual - Page 1
Multimedia Projector MODEL PLV-Z1 PLV-Z1BL Owner's Manual - Sanyo PLV Z1 | Owners Manual - Page 2
16 Lamp Replace Counter 45 17 Warning Temp. Indicator 46 18 Air Filter Care and Cleaning 46 Cleaning the Projection Lens 46 Troubleshooting 47 19 Indicators and Projector Condition 48 Technical Specifications 49 Dimensions 50 19 Configuration of Terminals 51 19 Optional Parts - Sanyo PLV Z1 | Owners Manual - Page 3
again, check operations and cable connections and try the solutions in the Troubleshooting section at the end of this manual. If the problem still persists, contact the sales dealer where you purchased the projector or the service center. SAFETY PRECAUTIONS WARNING : TO REDUCE THE RISK OF FIRE OR - Sanyo PLV Z1 | Owners Manual - Page 4
, be sure the service technician has used replacement parts specified by the manufacturer that have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or injury to persons. Upon completion of any service or repairs to this projector, ask the - Sanyo PLV Z1 | Owners Manual - Page 5
in an unsuitable transport case. This may cause damage to a projector. To transport a projector through a courier or transport service, consult your dealer for best way. NOTE Moving the projector from a cool temperature location to a warm temperature location may result in moisture condensation - Sanyo PLV Z1 | Owners Manual - Page 6
unless otherwise specified in the instructions. If such changes or modifications should be made, you could be required to stop operation of the equipment. Model Number Trade Name Responsible party Address Telephone No. : PLV-Z1, PLV-Z1BL : Sanyo : SANYO FISHER COMPANY : 21605 Plummer Street - Sanyo PLV Z1 | Owners Manual - Page 7
or service station if you are not sure of the type of power being supplied. Connect a projector with all peripheral equipment before turning a projector on. does not match your AC outlet, contact your sales dealer. Projector side AC Outlet side For the U.S.A. and Canada For Continental Europe Ground - Sanyo PLV Z1 | Owners Manual - Page 8
detects signal or any operation button is pressed. This projector is shipped with this function ON. N Lamp Mode Either the Bright mode or the Theater black mode is available in the Setting menu. The Theater black mode is suitable for seeing a movie since it makes the image best for a movie in - Sanyo PLV Z1 | Owners Manual - Page 9
Part Names and Functions Front CAUTION This projector is equipped with Cooling Fans for protection from overheating. Pay attention to the following to ensure proper ventilation and avoid a possible risk of fire and - Sanyo PLV Z1 | Owners Manual - Page 10
Part Names and Functions Bottom ADJUSTABLE FEET AND FEET LOCK LATCHES LAMP COVER AIR INTAKE VENTS AND AIR the top cabinet), especially screws and metallic parts. This area will become hot while the projector is used. This projector detects internal temperature and automatically controls speed of - Sanyo PLV Z1 | Owners Manual - Page 11
page 18.) Part Names and Functions SERVICE PORT JACK This jack is used to service this projector. * S-VIDEO INPUT JACK Connect the S-VIDEO output from video equipment to this jack. (Refer to page 17.) VIDEO INPUT JACK (VIDEO) Connect the composite video output from video equipment to VIDEO jack - Sanyo PLV Z1 | Owners Manual - Page 12
green in Power management mode. (p43) WARNING TEMP. READY LAMP REPLACE ON-OFF LAMP LAMP INDICATOR Becomes dim when the projector is turned on. And it is bright when the projector is in stand-by mode. POWER ON-OFF BUTTON Used to turn the projector on or off. (p19) MENU SELECT INPUT INPUT - Sanyo PLV Z1 | Owners Manual - Page 13
VIDEO 2 KEYSTONE S-VIDEO 3 COMPONENT COMPO 4 POWER ON-OFF BUTTON Used to turn the projector on or off. (p19) SCREEN BUTTON Used to select screen size. (p30, 41) POINT BUTTONS Used to select an item or adjust value in the onscreen menu. They are also used to pan the image in Digital zoom mode - Sanyo PLV Z1 | Owners Manual - Page 14
Part Names and Functions Remote Control Batteries Installation 1 Remove the battery compartment explosion if battery is replaced by an incorrect type. G Dispose of used batteries according to the instructions. Operating Range Point the remote control toward the projector (Infrared Remote Receiver - Sanyo PLV Z1 | Owners Manual - Page 15
. Keystone distortion of a projected image can be adjusted by menu operation or the remote control. (Refer to page 21 and 42.) ADJUSTABLE FEET CAUTION Tilt the projector within the adjustable range in order not to shorten the life of the lamp. Proper angle should be taken. Refer to page 5. FEET - Sanyo PLV Z1 | Owners Manual - Page 16
Installation Moving the Lens The Projection lens can be moved up and down with manual lens shift function. This function makes it easy to provide a projected image where you want. U/D ratio can be adjusted from 10 : 0 ~ 0 : 10 (refer to the - Sanyo PLV Z1 | Owners Manual - Page 17
for order.) COMPUTER IN Terminals of the Projector NOTE When selecting the video input with the "AUTO" on the remote control or through menu operation, the projector selects connection in the following order: 1st Y-Pb/Cb-Pr/Cr 2nd S-VIDEO 3rd VIDEO VIDEO Connect these 3 jacks Y - Pb/Cb - Pr/Cr - Sanyo PLV Z1 | Owners Manual - Page 18
shown in the table below depending on RESOLUTION MODE that you want to use before you turn on projector and computer. ON OFF ON DIP 123456 1 2 3 4 56 13" MODE (640 x 480) ON ON OFF OFF OFF OFF 16" MODE (832 x 624) OFF ON OFF ON OFF OFF 19" MODE (1024 x 768) OFF ON ON OFF OFF - Sanyo PLV Z1 | Owners Manual - Page 19
input source of either video or computer. (Refer to page 24 or 31.) Open the front cover. MAIN ON/OFF switch OFF ON Lamp mode Lamp mode Bright light (Bright mode) Light with head gray (Theater black mode) *Refer to page 43 for the Lamp mode. Turning Off the Projector 1 Press the POWER ON - Sanyo PLV Z1 | Owners Manual - Page 20
Basic Operation Focus Adjustment Rotate the FOCUS RING to adjust the projected picture focus. FOCUS RING Zoom Adjustment Move the ZOOM LEVER upward to make the image larger. Move the ZOOM LEVER downward to make the image smaller. ZOOM LEVER WIDE TELE 20 - Sanyo PLV Z1 | Owners Manual - Page 21
button on the remote control or select the Keystone in the Setting menu. (Refer to page 42.) The Keystone dialog box appears. 2 Correct POINT UP button to reduce the upper part of image, and press the KEYSTONE M button or the POINT DOWN button to reduce the lower part. • The arrows are white when - Sanyo PLV Z1 | Owners Manual - Page 22
Operation WARNING TEMP. READY LAMP REPLACE ON-OFF LAMP On-Screen Menu The projector has the on-screen menu that provides a variety of adjustment and settings. 1 Display the on-screen menu by pressing the MENU button on the top control or the remote control. A main menu appears. TOP CONTROL - Sanyo PLV Z1 | Owners Manual - Page 23
Keystone, Blue back, Display, Menu position, Logo, Ceiling, Rear, Power management, Power off confirmation, Lamp mode, Remote control, and Lamp counter reset. (Refer to page 42.) COMPUTER MENUS INPUT SOURCE SELECTION: select input source either Computer or Video [Auto, Video, S-Video, (Y-Pb/CbPr/Cr - Sanyo PLV Z1 | Owners Manual - Page 24
(The input source that is selected last is selected when the projector is turned on.) If the projector cannot reproduce proper video source, select correct input source through menu operation on the next page. INPONU-OTFF buttoLnAMP Video Computer RGB Scart Input To select RGB Scart 21-pin - Sanyo PLV Z1 | Owners Manual - Page 25
button, and then press the POINT RIGHT button to enter the sub-menu. Input Source Selection menu Input Source Selection menu 2 Choose the Video with the POINT UP/DOWN button and press the POINT RIGHT button. The source selection menu appears. 3 Move the pointer to the source that you want to - Sanyo PLV Z1 | Owners Manual - Page 26
-N, select either PAL-M or PAL-N manually. PAL / SECAM / NTSC / NTSC4.43 / PAL-M / PAL-N If the projector cannot reproduce proper video image, select a specific system among PAL, SECAM, NTSC, NTSC 4.43, PAL-M, and PAL-N. Close the Video System Selection menu. Video System Selection (Y-Pb/Cb-Pr/Cr - Sanyo PLV Z1 | Owners Manual - Page 27
the SELECT button to activate it. The level being selected. Standard Normal picture adjustment preset on this projector. Cinema Picture level adjusted for the picture with fine tone. IMAGE 1~4 User preset picture adjustment in Image Level Adjustment menu (p28, 29). Close the Image Level Selection - Sanyo PLV Z1 | Owners Manual - Page 28
Video Input Image Level Adjustment 1 Press the MENU button, and the main menu appears. Select the Image Level Adjustment menu with the POINT UP/DOWN button, and then press the POINT RIGHT button to enter the sub-menu. Image Level Adjustment menu Image Level Adjustment menu 2 Choose the item - Sanyo PLV Z1 | Owners Manual - Page 29
vivid image according to image condition. Reset Reset all adjustment before the data is stored. (The Reset does not work for the stored data.) Store Store the adjustment data. Quit Close the Image Level Adjustment menu. NOTE : Tint cannot be adjusted when the video system is PAL, SECAM, PAL-M or - Sanyo PLV Z1 | Owners Manual - Page 30
uniformly. This function can be used for providing a squeezed video signal at wide video aspect ratio of 16 : 9. When your video equipment (such as DVD) has 16 : 9 output mode, select 16 : 9 and select the Full on this Screen Size Adjustment menu to provide better quality. Zoom Provides an image to - Sanyo PLV Z1 | Owners Manual - Page 31
LAMP REPLACE You can select Computer input or Video input with the INPUT button. ON-OFF LAMP INPUT button (The input source that is selected last is selected when the projector is turned on.) Computer If the projector cannot reproduce proper image, select a correct input source through menu - Sanyo PLV Z1 | Owners Manual - Page 32
Troubleshooting section on page 47.) Mode 1 User preset adjustment in Computer Adjustment (Manual). Adjustment data can be stored Mode 1 - 5. SVGA 1 Computer systems provided in the projector. The projector chooses proper system and displays it. *Mode 1 and SVGA 1 are examples. 1 Press the MENU - Sanyo PLV Z1 | Owners Manual - Page 33
) 50.00 (Interlace) NOTE Specifications are subject to change without notice. This projector cannot display any resolution higher than 1280 X 1024. If your computer's screen resolution is higher than 1280 X 1024, reset the resolution to the lower before connecting projector. The image data in other - Sanyo PLV Z1 | Owners Manual - Page 34
by selecting Mode in the Computer System Selection menu. NOTE manual adjustments are required. (Refer to page 35-37.) The Auto PC Adjustment function cannot be operated when "720p (HDTV)," "1035i (HDTV)", or "1080i (HDTV)" is selected in the Computer System menu (p32). The Computer Adjustment menu - Sanyo PLV Z1 | Owners Manual - Page 35
signal formats. This projector has 5 independent memory areas to memorize those parameters manually adjusted. This enables you to recall the setting for a specific computer whenever you use it. 1 Press the MENU button, and the main menu appears. Select the Computer Adjustment menu with the POINT - Sanyo PLV Z1 | Owners Manual - Page 36
the POINT UP/DOWN button, and press the SELECT button. Select "Yes" with the SELECT button and close the menu by pressing the SELECT button at the Quit. To store adjustment data. Vacant Mode This Mode has parameters being stored. 5 To clear the adjustment parameters previously set, select the - Sanyo PLV Z1 | Owners Manual - Page 37
Select the area displayed with this projector. Select the resolution at the Display area dialog box. NOTE : The Display area, Display area (H/V) and Full screen cannot be adjusted when "1035i (HDTV)" or "1080i (HDTV)" is selected in the Computer System Selection menu (p32). Display area Press the - Sanyo PLV Z1 | Owners Manual - Page 38
Normal picture adjustment preset on this projector. Real Picture adjustment improved in reproduction of halftones. This adjustment is suitable for providing better image in brighter place. IMAGE 1~4 User preset picture adjustment in the Image Level Adjustment menu (p39, 40). The level being - Sanyo PLV Z1 | Owners Manual - Page 39
to the sub-menu. Press the SELECT button at this icon to display other items. 3 To store the adjustment data, select the Store with the POINT UP/DOWN button and press the POINT RIGHT button. Reset To reset to previous level, select the Reset with the POINT UP/DOWN button and press the POINT - Sanyo PLV Z1 | Owners Manual - Page 40
is "ON", it automatically enhances contrast of bright and dark part of image. Auto fleshtone When this function is "ON", it produces more vivid image according to image condition. Reset Reset all adjustment before the data is stored. (The Reset does not work for the stored data.) Store Store the - Sanyo PLV Z1 | Owners Manual - Page 41
when "1035i (HDTV)", "1080i (HDTV)", or "720p(HDTV)" is selected in the Computer System menu (p32). The True and Digital zoom cannot be selected when "RGB" is selected in the Computer System menu (p32). Panning function may not operate properly if the computer system (Mode 1-5) stored in the - Sanyo PLV Z1 | Owners Manual - Page 42
vertically, select the Keystone. The onscreen menu disappears and the Keystone dialog box is displayed. Correct keystone distortion by pressing the POINT UP/DOWN button. Refer to Keystone Adjustment on page 21. Blue back When this function is "On," the projector produces a blue image while input - Sanyo PLV Z1 | Owners Manual - Page 43
batteries of the remote control are replaced, the remote control code automatically returns to the initial code (Code 2). Lamp counter reset This function is used to reset the Lamp Replace Counter. When replacing the Projection lamp, reset the Lamp Replace Counter by using this function. Refer to - Sanyo PLV Z1 | Owners Manual - Page 44
COVER HANDLE LAMP ASSEMBLY SCREW ORDER REPLACEMENT LAMP Replacement Lamp can be ordered through your dealer. When ordering a Projection Lamp, give the following information to the dealer. G Model No. of your projector : G Replacement Lamp Type No. : PLV-Z1 / PLV-Z1BL POA-LMP54 (Service Parts No - Sanyo PLV Z1 | Owners Manual - Page 45
Appendix Lamp Replace Counter Be sure to reset the Lamp Replace Counter after the Lamp assembly is replaced. After the Lamp Replace Counter is reset, the LAMP REPLACE indicator stops lighting. 1 Turn on the projector and press the MENU button. The main menu appears. Select the Setting menu with - Sanyo PLV Z1 | Owners Manual - Page 46
, and disconnect AC Power Cord from the AC outlet. MENU INPUT 2 Turn over the projector and remove the Air filter by pulling the latch upward. SELECT LATCH 3 Clean the Air filter with a brush or wash out dust and particles. 4 Replace the Air filter properly. Make sure that it is fully inserted - Sanyo PLV Z1 | Owners Manual - Page 47
Appendix Troubleshooting Before calling your dealer or service center for assistance, check the following: • Make sure you have connected the projector to video equipment or your computer as described on page 17 and 18. • Check cable connection. Verify that all video, computer, and power cord are - Sanyo PLV Z1 | Owners Manual - Page 48
44) Off Yellow Light The projection lamp needs to be replaced. The projector is operating normally. Off If the problem still persists after following all operating instructions, contact the sales dealer where you purchased the projector or the service center. Give the model number and explain - Sanyo PLV Z1 | Owners Manual - Page 49
Appendix Technical Specifications Projector Type Dimensions (W x H x D) Net Weight LCD Panel System Panel Resolution Number of Pixels Color System High Definition TV Signal Scanning Frequency Projection Image size (Diagonal) Projection Lens Throw Distance Projection Lamp Video Input Jacks Computer - Sanyo PLV Z1 | Owners Manual - Page 50
Appendix Unit : inch (mm) 11.8˚ (Max.) Dimensions 13.11 (333) WARNING TEMP. READY LAMP REPLACE ON-OFF LAMP MENU SELECT INPUT 9.70 (246.5) 4.27 (108.5) 50 - Sanyo PLV Z1 | Owners Manual - Page 51
6 15 14 13 12 11 SERVICE PORT CONNECTOR Terminal : Mini DIN 8-PIN *This port is only used for service. Pin Configuration 876 5 43 21 8 GND Appendix Optional Parts The parts listed below are optionally supplied. When ordering those parts, give name and Type No. of it to the sales dealer. G MAC - Sanyo PLV Z1 | Owners Manual - Page 52
Printed in Japan Part No. 610 304 8642 (1AA6P1P3626A- M4JAB) SANYO Electric Co., Ltd.
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
 |
 |
Multimedia Projector
MODEL
PLV-Z1
PLV-Z1BL
Owner’s Manual