Sanyo WXU700 Instruction Manual, PLC-WXU700 Network Set Up Macintosh - Page 105

Troubleshooting, Wireless LAN

Get Sanyo WXU700 - WXGA LCD Projector PDF manuals and user guides
UPC - 086483074219
View all Sanyo WXU700 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 105 highlights

Troubleshooting Troubleshooting If you have any trouble in setup or operation of the projector, refer to the troubleshooting items and check the relevant matters described. ■ The computer cannot connect projectors. Wired LAN Is the LAN cable connected to the projector properly? Is the LINK/ACT lamp of the LAN terminal lighting properly? Not lighting : The LAN setting of the projector is set "On"? See "Wired setting" in the projector menu. The LAN cable is connected to the network HUB properly? Wireless LAN Is the WIRELESS indicator on the side panel of the projector lighting? If there are not any problems, confirm the LAN setting again. Refer to the next item. If the computer supports Wireless LAN, activate the Network Capture 5 and try to connect with the Easy setting button. Refer to "5. Wireless LAN configuration" ➔ "Easy wireless settings" (☞p.41). If the wireless LAN card provides the firewall function itself, set up to disable its function. ■ Cannot connect with easy wireless setting function The projector should be set up previously to complete the easy wireless setting. Depending on the wireless LAN card or computer, this easy wireless setting function may not be available. When your computer is using multiple network adaptors which are available in the setting, and their IP address groups are the same as shown below, this easy wireless setting function may not be succeeded. [For example] IP address setting of Wired LAN adaptor in your computer : 169.254.*.* IP address setting of Wireless LAN adaptor in your computer : 169.254.*.* ■ Wireless LAN Connection cannot be established. AdHoc Mode: When selecting LAN4(factory default setting) Check each item in the Wireless Setting menu of the projector as follows: *IP Address Is the address appropriate? Should not be the same as the other IP address. *Sub net Should be the factory default value, 255.255.0.0. *Gateway Should be the factory default value, 255.255.255.255 *Network Type Should be AdHoc mode *ESSID/SSID Should be the same as the setting of computer ->Check the setting for the computer *Is the Wireless channel set as 11 both for the computer and the projector? -> The factory default channel of the projector is 11. *WEP (Wired Equivalent Privacy) Should be disabled. 105

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
10´
If you have any trouble in setup or operation of the projector, refer to the troubleshooting items
and
check the relevant matters described.
Troubleshooting
■
The computer cannot connect projectors.
Wired LAN
Is the LAN cable
connected to the projector properly?
Is the LINK/ACT lamp of the LAN terminal lighting properly?
Not lighting : The LAN setting of the projector is set “On”?
See “Wired setting” in
the projector menu.
The LAN cable is connected to the network HUB properly?
Wireless LAN
Is the WIRELESS indicator on the side panel of the projector lighting?
If there are not any problems, confirm the LAN setting again. Refer to the next item.
If the computer supports Wireless LAN, activate the Network Capture 5 and try to connect with the
Easy setting button. Refer to “5. Wireless LAN configuration”
➔
“Easy wireless settings” (
☞
p.41).
If the wireless LAN card provides the firewall function itself, set up to disable its function.
■
Wireless LAN Connection cannot be established.
AdHoc Mode:
When selecting LAN4(factory default setting)
Check each item in the Wireless Setting menu of the projector as follows:
*IP Address
...............................
Is the address appropriate? Should not be the same as the other IP address.
*Sub net
................................
Should be the factory default value, 255.255.0.0.
*Gateway
..............................
Should be the factory default value, 255.255.255.255
*Network Type
....
................
Should be AdHoc mode
*ESSID/SSID
.........................
Should be the same as the setting of computer
->Check the setting for the computer
*Is the Wireless channel set as 11 both for the computer and the projector?
-> The factory default channel of the projector is 11.
*WEP (Wired Equivalent Privacy) Should be disabled.
Troubleshooting
■
Cannot connect with easy wireless setting function
The projector should be set up previously to complete the easy wireless setting.
Depending on the
wireless LAN card or computer, this easy wireless setting function may not be available.
When your computer is using multiple network adaptors which are available in the setting, and their IP
address groups are the same as shown below, this easy wireless setting function may not be succeeded.
[For example]
IP address setting of Wired LAN adaptor in your computer
: 169.254.*.*
IP address setting of Wireless LAN adaptor in your computer
: 169.254.*.*