Sanyo WXU700 Instruction Manual, PLC-WXU700 Network Set Up Macintosh - Page 28

±·

Chapter 4 Wired LAN configurations

Setting Procedure

Setting procedures and contents differ depending on the LAN installation location.

When installing, consult your system administrator to set up the LAN appropriately.

Connect the shielded LAN cable to the LAN connection terminal of the projector.

Network environment settings

Set the Wired LAN network through the projector menu. Detailed network settings will be made with

browser. Refer to “6. Basic setting and operation” (pp.45-64). First, complete the settings described in

this chapter before performing steps in “6. Basic setting and operation.”

1. Turn on the projector and select “Network” from the input menu of the projector.

2. Select “LAN mode select” in the Network menu, and press Point

8

or

SELECT

button.

3. Select similar LAN environment among Wired1, 2 and 3 with the Point

ed

buttons. Then the Menu

will disappear, the “Please wait...” message will appear, and switching operation will start. Switching

will take a while and after completing the operation, the “Ready for use” message will appear, and the

projector’s LINK/ACT Lamp will be on or blink.

Connecting to the LAN line

LAN Connection

Terminal

* When the LAN setting is “Off”, the two lamps will not be on.

ACT Lamp (Orange)

When the projector is

connected to the 100 Base-

TX network, light or blink as

follows;

- Light when connecting to

the network.

- Blink when sending or

receiving the data.

LINK lamp (Green)

Light green when the

projector is connected to the

network.

LAN Cable**

** Please use a shielded LAN cable .

Section	Page
Compliance	2
Safety instructions	4
Table of contents	5
Operating environment and configuration	7
Required operating environment for computers	7
Network specifications of the projector	8
Useful guide to the network function	9
How to project the computer screen’s image via the network	9
How to setup or control the projector by using a PC via the network	9
How to use all functions concerning the network	9
1. About LAN functions	11
LAN functions and the features	12
Image projecting system via LAN	12
An example of the connection	13
LAN connection modes	14
2. Setup procedures	17
Installing the software	19
3. Names and functions of the operation screen	23
Network connection standby display	24
Network Capture 5 window	25
4. Wired LAN configurations	27
Connecting to the LAN line	28
Network environment settings	28
Confirming the operation	30
Network PIN code	32
Network information	32
Wired factory default	33
Wired LAN factory default settings	34
5. Wireless LAN configurations	35
Setting the network environment	36
Setting procedures	36
Configuring security with the projector	38
Easy wireless setting	41
Network PIN code	42
Network information	42
Wireless factory default	42
WIRELESS indicator display	43
Wireless LAN factory default settings	44
6. Basic setting and operation	45
Starting up the Browser	46
How to use the setting page	48
Initial setting	50
Network configuration	53
Configuring wireless LAN setting and security setting	55
E-mail setting	57
SNMP setting	61
7. Controlling the projector	65
Power control and status check	66
Controls	68
PC adjustment	72
Setting up the projector	73
Timer setting	76
Projector information	79
Multi-control	81
8. Network capture functions	87
About Network Capture function	88
Using the Real Time Capture	91
Error information	96
9. Appendix	97
Use of telnet	98
Web browser setting	100
Firewall setting for MAC OS X v 10.4	103
Firewall setting for MAC OS X v 10.5	104
Troubleshooting	105

Sanyo WXU700 Instruction Manual, PLC-WXU700 Network Set Up Macintosh - Page 28

Connecting to the LAN line, Network environment settings, Setting Procedure

Page 28 highlights