Home » Seagate Manuals » Hard Drives » Seagate ST340015A » Manual Viewer

Seagate ST340015A Product Manual - Page 17

Operating power and current

Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

Barracuda 5400.1 Product Manual, Rev. F 9 2.9.1 Power consumption Power requirements for the drives are listed in the table on page 10. Typical power measurements are based on an average of drives tested, under nominal conditions, using 5.0V and 12.0V input voltage at 25°C ambient temperature. • Spinup power Spinup power is measured from the time of power-on to the time that the drive spindle reaches operating speed. • Seek mode During seek mode, the read/write actuator arm moves toward a specific position on the disc surface and does not execute a read or write operation. Servo electronics are active. Seek mode power represents the worst-case power consumption, using only random seeks with read or write latency time. This mode is not typical and is provided for worst-case information. • Read/write power and current Read/write power is measured with the heads on track, based on a 16-sector write followed by a 32-msec delay, then a 16-sector read followed by a 32msec delay. • Operating power and current Operating power is measured using 40 percent random seeks, 40 percent read/write mode (1 write for each 10 reads) and 20 percent drive idle mode. • Idle mode power Idle mode power is measured with the drive up to speed, with servo electronics active and with the heads in a random track location. • Standby mode During Standby mode, the drive accepts commands, but the drive is not spinning, and the servo and read/write electronics are in power-down mode.

Section	Page
1.0 Introduction 1	5
2.0 Drive specifications 3	5
2.1 Specification summary table 3	5
2.2 Formatted capacity 6	5
2.3 Default logical geometry 6	5
2.4 Physical organization 6	5
2.5 Recording and interface technology 7	5
2.6 Physical characteristics 7	5
2.7 Seek time 8	5
2.8 Start/stop times 8	5
2.9 Power specifications 8	5
2.9.1 Power consumption 9	5
2.9.2 Conducted noise 12	5
2.9.3 Voltage tolerance 12	5
2.9.4 Power-management modes 12	5
2.10 Environmental specifications 13	5
2.10.1 Ambient temperature 13	5
2.10.2 Temperature gradient 14	5
2.10.3 Humidity 14	5
2.10.4 Altitude 14	5
2.10.5 Shock 15	5
2.10.6 Vibration 15	5
2.11 Acoustics 16	5
2.12 Electromagnetic immunity 17	5
2.13 Reliability 17	5
2.14 Agency certification 18	5
2.14.1 Safety certification 18	5
2.14.2 Electromagnetic compatibility 18	5
2.14.3 FCC verification 19	5
3.0 Configuring and mounting the drive 21	5
3.1 Handling and static discharge precautions 21	5
3.2 Breather filter hole precautions 22	5
3.3 Jumper settings 23	5
3.3.1 Master/slave configuration 23	5
3.3.2 Cable select option 23	5
3.3.3 Ultra ATA/100 cable 24	5
3.4 Drive mounting 24	5
4.0 ATA interface 27	5
4.1 ATA interface signals and connector pins 27	5
4.1.1 Supported ATA commands 29	6
4.1.2 Identify Device command 31	6
4.1.3 Set Features command 36	6
4.1.4 S.M.A.R.T. commands 38	6
5.0 Seagate Technology support services 39	6
Figure 1. Typical 5V startup and operation current profile 11	7
Figure 2. Typical 12V startup and operation current profile 11	7
Figure 3. Breather filter hole location 22	7
Figure 4. Master/slave jumper settings 23	7
Figure 5. Ultra ATA cable connectors 24	7
Figure 6. Mounting dimensions-top, side and end view 25	7
Figure 7. I/O pins and supported ATA signals 28	7
1.0 Introduction	9
2.0 Drive specifications	11
2.1 Specification summary table	11
2.2 Formatted capacity	14
2.3 Default logical geometry	14
2.4 Physical organization	14
2.5 Recording and interface technology	15
2.6 Physical characteristics	15
2.7 Seek time	16
2.8 Start/stop times	16
2.9 Power specifications	16
2.9.1 Power consumption	17
2.9.1.1 Typical current profile	19
2.9.2 Conducted noise	20
2.9.3 Voltage tolerance	20
2.9.4 Power-management modes	20
2.10 Environmental specifications	21
2.10.1 Ambient temperature	21
2.10.2 Temperature gradient	22
2.10.3 Humidity	22
2.10.3.1 Relative humidity	22
2.10.3.2 Wet bulb temperature	22
2.10.4 Altitude	22
2.10.5 Shock	23
2.10.5.1 Operating shock	23
2.10.5.2 Nonoperating shock	23
2.10.6 Vibration	23
2.10.6.1 Operating vibration	23
2.10.6.2 Nonoperating vibration	23
2.11 Acoustics	24
2.12 Electromagnetic immunity	25
2.13 Reliability	25
2.14 Agency certification	26
2.14.1 Safety certification	26
2.14.2 Electromagnetic compatibility	26
2.14.3 FCC verification	27
3.0 Configuring and mounting the drive	29
3.1 Handling and static discharge precautions	29
3.2 Breather filter hole precautions	30
3.3 Jumper settings	31
3.3.1 Master/slave configuration	31
3.3.2 Cable select option	31
3.3.3 Ultra ATA/100 cable	32
3.4 Drive mounting	32
4.0 ATA interface	35
4.1 ATA interface signals and connector pins	35
4.1.1 Supported ATA commands	37
4.1.2 Identify Device command	39
4.1.3 Set Features command	44
4.1.4 S.M.A.R.T. commands	46
5.0 Seagate Technology support services	47
A	53
B	53
C	53
D	53
E	53
F	53
G	54
H	54
I	54
J	54
K	54
L	54
M	54
N	54
O	54
P	54
R	55
S	55
T	55
U	56
V	56