Sony AIR-SA15Ti Operating Instructions (AIRSA20PK) - Page 27

Listening to the radio using the S-AIR connection

Get Sony AIR-SA15Ti - Wireless Audio Transmitter Component PDF manuals and user guides View all Sony AIR-SA15Ti manuals
Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

Operations To use the main unit as a battery charger You can use the main unit as a battery charger for the iPod when the main unit is on. The charging begins when the iPod is placed on the iPod connector. The charging status appears in the iPod display. For details, refer to the user's guide of your iPod. To stop charging the iPod, remove the iPod or turn off the main unit. Notes  When placing or removing the iPod, handle the iPod in the same angle as that of the iPod connector on the main unit and do not twist or sway the iPod to prevent connector damage.  Do not carry the main unit with an iPod set on the connector. Doing so may cause a malfunction.  When placing or removing the iPod, brace the main unit with one hand and take care not to press the controls of the iPod by mistake.  Before disconnecting the iPod, pause playback.  You cannot adjust the volume using the main unit.  The volume level does not change even if adjusted on the iPod.  The main unit is designed for iPod only. You cannot connect any other portable audio players.  Depending on the iPod model you are using and its status, operations using the main unit and the sub units may not be accepted or the wrong operations may be performed.  Sony cannot accept responsibility in the event that data recorded to iPod is lost or damaged when using an iPod with this S-AIR product. Listening to the radio using the S-AIR connection Using the main unit 1 Select the tuner channel. When the S-AIR mode is set to "PARTY": Press PARTY CH on the remote repeatedly until "FM" or "AM" appears in the display. When the S-AIR mode is set to "MULTI SOURCE": The tuner channel is internally activated. Go to step 2. 2 Select "FM" or "AM." Press BAND repeatedly. 3 Perform automatic tuning. Press and hold TUNING +/ on the remote (or TUNING/SELECT +/ on the unit) until the frequency indication changes and then release. "AUTO" lights up in the display. Scanning stops automatically when a station is tuned in, and then "TUNED" and "ST" (for FM stereo programs only) appear.  Continued 27GB

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
±µ
GB
Operations
To use the main unit as a battery
charger
You can use the main unit as a battery
charger for the iPod when the main unit
is on.
°e charging begins when the iPod
is placed on the iPod connector. °e
charging status appears in the iPod
display. For details, refer to the user’s
guide of your iPod.
To stop charging the iPod, remove the
iPod or turn off the main unit.
Notes
When placing or removing the iPod, handle
the iPod in the same angle as that of the
iPod connector on the main unit and do not
twist or sway the iPod to prevent connector
damage.
Do not carry the main unit with an iPod
set on the connector. Doing so may cause a
malfunction.
When placing or removing the iPod, brace
the main unit with one hand and take care
not to press the controls of the iPod by
mistake.
Before disconnecting the iPod, pause
playback.
You cannot adjust the volume using the main
unit.
°e volume level does not change even if
adjusted on the iPod.
°e main unit is designed for iPod only. You
cannot connect any other portable audio
players.
Depending on the iPod model you are using
and its status, operations using the main unit
and the sub units may not be accepted or the
wrong operations may be performed.
Sony cannot accept responsibility in the
event that data recorded to iPod is lost or
damaged when using an iPod with this S-AIR
product.
Listening to the
radio using the S-AIR
connection
Using the main unit
1
Select.the.tuner.channel±
When the S-AIR mode is set to
“PARTY”:
Press PARTY CH on the remote
repeatedly until “FM” or “AM”
appears in the display.
When the S-AIR mode is set to
“MULTI SOURCE”:
°e tuner channel is internally
activated. Go to step 2.
2
Select.“FM”.or.“AM±”
Press BAND repeatedly.
3
Perform.automatic.tuning±
Press and hold TUNING +/
on
the remote (or TUNING/SELECT
+/
on the unit) until the frequency
indication changes and then release.
“AUTO” lights up in the display.
Scanning stops automatically when
a station is tuned in, and then
“TUNED” and “ST” (for FM stereo
programs only) appear.
Continued