Sony CCD TRV16 Service Manual - Page 2

Input and output connectors Video output Phono jack, 1 Vp-p, 75 ohms, unbalanced Audio output Monaural, Phone jack, 327 mV (at output impedance 47 kilohms) impedance less than 2.2 kilohms RFU DC OUT Special minijack, DC 5V Earphone jack (TRV series only) Monaural minijack (ø 3.5 mm) LANC control jack Stereo mini-minijack (ø 2.5 mm) MIC jack Mini jack, 0.388mV low impedance with 2.5 to 3.0 V DC, output impedance 6.8 kilohms (ø 3.5 mm) : Monaural type Speaker (TRV series only) Dynamic speaker General Power requirements 7.2 V (battery pack) 8.4 V (AC power adaptor) Averege power consumption(when using the battery pack) During camera recording CCD-TR416/TR416PK/TR516/ TR516PK : 2.4 W CCD-TR315/TR716 : 2.5 W During camera recording using LCD CCD-TRV16/TRV16PK/TRV36/ TRV36PK : 3.1 W CCD-TRV43/TRV46/TRV46PK : 3.2 W Viewfinder CCD-TRV16/TRV16PK/TRV36/ TRV36PK : 2.5 W CCD-TRV43/TRV46/TRV46PK : 2.6 W Operating temperature 32°FC to 104°F (C0°C to 40°C) Storage temperature -4°FC to 140°F (-20°C to +60°C) Dimentions (Approx.) 4 1/4 x 4 1/4 x 7 5/8 in. 107 x 107 x 193 mm)(w/h/d) Mass (Approx.) CCD-TR315/TR716 : 1 lb 11 oz (790 g) CCD-TR416/TR416PK/TR516/ TR516PK : 1 lb 11 oz (780 g) CCD-TRV16/TRV16PK/TRV36/ TRV36PK : 1 lb 14 oz (870 g) CCD-TRV43/TRV46/TRV46PK : 1 lb 15 oz (880 g) excluding the battery pack, lithium battery, cassette and shoulder strap 2 lb 3 oz (1 kg) including the battery pack NP-F330, lithium battery CR2025, cassette and shoulder strap Microphone Monaural type Supplied accessories See page 4. AC power adaptor Power requirements 100 -240 V AC, 50/60 Hz Power consumption 23 W Output voltage DC OUT: 8.4 V, 1.5 A in operating mode Operating temperature 32°F to 104°F(0°C to 40°C) Storage temperature -4°F to +140°F(-20°C to +60°C) Dimentions (Approx.) 5 x 1 9/16 x 2 1/2 in. (125 x 39 x 62 mm)(w/h/d) excluding projecting parts Mass (Approx.) 9.8 oz (280 g) excluding power cord Design and specifications are subject to change without notice. • Abbreviation Canadian model is abbreviated as CND. Brazilian model is abbreviated as BR. SAFETY CHECK-OUT After correcting the original service problem, perform the following safety checks before releasing the set to the customer: 1. Check the area of your repair for unsoldered or poorly-soldered connections. Check the entire board surface for solder splashes and bridges. 2. Check the interboard wiring to ensure that no wires are "pinched" or contact high-wattage resistors. 3. Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair. Point them out to the customer and recommend their replacement. 4. Look for parts which, though functioning, show obvious signs of deterioration. Point them out to the customer and recommend their replacement. SAFETY-RELATED COMPONENT WARNING !! COMPONENTS IDENTIFIED BY MARK ! OR DOTTED LINE WITH MARK ! ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. 5. Check the B+ voltage to see it is at the values specified. 6. Flexible Circuit board Repairing • Keep the temperature of the soldering iron around 270°C during repairing. • Do not touch the soldering iron on the same conductor of the circuit board (within 3 times). • Be careful not to apply force on the conductor when soldering or unsoldering. ATTENTION AU COMPOSANT AYANT RAPPORT À LA SÉCURITÉ!! LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE ! SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÉCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÉCES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.