Sony MZ-R700 Operating Instructions - Page 61

Hi Dc In, Low Batt, Mem Over, No Copy, No Disc, No Signal, P/b Only, Protected, Insert An Md.

Get Sony MZ-R700 PDF manuals and user guides View all Sony MZ-R700 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 61 highlights

Hi DC in • Voltage of the power supply is too high (The supplied AC power adaptor is not used). - Use the supplied AC power adaptor. HOLD • The recorder is locked. - Move HOLD against the arrow to unlock the recorder (pages 12, 38). LOW BATT • Battery is weak. - Charge the rechargeable battery or replace the dry battery (page 11). MEM OVER • You tried to record with the recorder placed where it receives continuous vibration. - Put the recorder on a stable place, and start recording again. NO COPY • You tried to make a copy from a disc that is protected by the Serial Copy Management System. You cannot make copies from a digitally connected source which was itself recorded using digital connection. - Use analog connection instead (page 23). NO DISC • You tried to play or record with no disc in the recorder. - Insert an MD. NO SIGNAL • The recorder could not detect digital input signals. - Make sure that the source is connected firmly (page 14). P/B ONLY • You tried to record or edit on a premastered MD (P/B stands for "playback"). - Insert a recordable MD. PROTECTED • You tried to record or edit on a MD with the tab in the recordprotect position. - Slide the tab back (page 54). 61

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
61
Hi DC in
•
Voltage of the power supply is too high (The supplied AC power
adaptor is not used).
—
Use the supplied AC power adaptor.
HOLD
•
The recorder is locked.
—
Move HOLD against the arrow to unlock the recorder (pages 12,
38).
LOW BATT
•
Battery is weak.
—
Charge the rechargeable battery or replace the dry battery
(page 11).
MEM OVER
•
You tried to record with the recorder placed where it receives
continuous vibration.
—
Put the recorder on a stable place, and start recording again.
NO COPY
•
You tried to make a copy from a disc that is protected by the Serial
Copy Management System. You cannot make copies from a
digitally connected source which was itself recorded using digital
connection.
—
Use analog connection instead (page 23).
NO DISC
•
You tried to play or record with no disc in the recorder.
—
Insert an MD.
NO SIGNAL
•
The recorder could not detect digital input signals.
—
Make sure that the source is connected firmly (page 14).
P/B ONLY
•
You tried to record or edit on a premastered MD (P/B stands for
“
playback
”
).
—
Insert a recordable MD.
PROTECTED
•
You tried to record or edit on a MD with the tab in the record-
protect position.
—
Slide the tab back (page 54).