Sony SPP-N1003 Operating Instructions - Page 3

Making and receiving calls Making calls TALK/BATT LOW lamp 2 (* TONE) Microphone (FLASH) VOL switch 4 (REDIAL/PAUSE) 1 Pick up the handset from the base unit. 2 Press (TALK), and wait until the TALK/BATT LOW lamp lights up. The dialing keys light up. You then hear a dial tone. If you hear beeps, move closer to the base unit. 3 Dial the phone number. 4 When you're done talking, press (OFF). The TALK/BATT LOW lamp goes off. (CHANNEL/RINGER) Receiving calls 1 When you hear the phone ring; • Press (TALK) (or any key except (OFF)). or • Pick up the handset from the base unit when the handset is placed on the base unit. The TALK/BATT LOW lamp lights up. 2 When you're done talking, replace the handset on the base unit or press (OFF). The TALK/BATT LOW lamp goes off. Additional tasks To Do this Adjust the handset Set the VOL switch to H (high), M (middle) or L (low). volume Switch to tone Press (* TONE) after you're connected. dialing temporarily The line will remain in tone dialing until disconnected. Set the ringer type While the handset is not in use, press (CHANNEL/RINGER). Each press of (CHANNEL/RINGER) switches the ringer type by one of four type. Switch to another call ("call waiting service"*) Press (FLASH). Press the button again to get back to the first caller. * You need to subscribe to the service from your telephone company. Notes • Do not cover the microphone during the conversation; otherwise, the other party cannot hear your voice. • If you hear beeps during the conversation, move closer to the base unit; otherwise, the call will be disconnected after 15 seconds. Note that, however, you may not hear beeps if it's noisy on the handset. If interference occurs on the handset When you press (TALK), the handset automatically searches for the channel with the best reception. However, if you notice interference during a conversation, move closer to the base unit. If interference persists, press (CHANNEL/RINGER) to switch to another channel to improve the sound quality of your telephone conversation. Note If you hear five short beeps when you press (CHANNEL/RINGER), move closer to the base unit. If the handset battery becomes weak during a call The handset will beep every three seconds with the TALK/BATT LOW lamp flashing at the same time. Finish your call and charge the battery pack. Caution If this occurs, you cannot use the handset without charging it for more than one minutes. Redialing 1 Press (TALK), and wait until the TALK/BATT LOW lamp lights up. 2 Press (REDIAL/PAUSE) to redial the number last dialed. Note If the number exceeds 32 digits, the beeps will alert you that the number cannot be dialed. To erase the last phone number dialed Press (REDIAL/PAUSE) twice. The number will be erased from the memory, and you'll hear a long confirmation beep. Speed dialing You can dial with a touch of a few keys by storing a phone number on a dialing key. Storing phone numbers TALK/BATT LOW lamp 1, 5 1 Press (PGM). The TALK/BATT LOW lamp flashes. 2 Press (SPEED DIAL). The dialing keys light up. 3 Press one of the dialing keys ((0) to (9)) to store a phone number on. You hear a confirmation beep. 4 Enter the phone number you want to store. You can enter up to 20 digits, 2 including a tone and a pause, each of which is counted as one digit. 5 Press (PGM). (REDIAL/PAUSE) You hear a long confirmation beep, and number is stored. The TALK/ BATT LOW lamp goes off. Note Do not allow more than 20 seconds to elapse between each step of the procedure. Tips • If you enter a wrong number, press (PGM), then start from the beginning. • Affix the supplied directory to a desired place. To store a number to be dialed via Private Branch Exchange (PBX) Before entering a phone number in step 4, do as follows: 1 Enter the outside line access digit (e.g., 9). 2 Press (REDIAL/PAUSE). To change a stored number Store a new number, as described previously. Note You can replace the stored number with a new number, but you cannot just erase it. Making calls with speed dialing 1 Press (TALK) and wait until the TALK/BATT LOW lamp lights up. The dialing keys light up. 2 Press (SPEED DIAL). 3 Enter the desired speed dialing number ((0) to (9)). The phone number stored in the speed dialing number will be dialed. Paging You can page the handset from the base unit. Note that you cannot page if the handset is in use. Press (HANDSET LOCATOR). The handset rings for about one minute. To end the page, press (OFF) on the handset. (HANDSET LOCATOR) Mounting the base unit on a wall 1 Attach the telephone line cord and AC power adaptor cord to the base unit. Bundle the loose telephone line cord or AC power adaptor cord, if necessary. 2 Plug the telephone line cord into the telephone outlet, and hook the base unit to the wall plate as illustrated. Plug the AC power adaptor to an AC outlet. Then raise the antenna so that it points towards the ceiling. 1 Bundle the loose telephone line cord or AC power adaptor cord, if necessary. 2 Wall plate Telephone line cord AC power AC outlet adaptor cord AC power adaptor