Sony STR-DE598 Operating Instructions - Page 51

Specifications - protect mode

Get Sony STR-DE598 - A/v Receiver PDF manuals and user guides View all Sony STR-DE598 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 51 highlights

Additional Information Error messages If there is a malfunction, the display shows a message. You can check the condition of the receiver by the message. Refer to the following table to solve the problem. DEC. EROR Appears when the signal which the receiver cannot decode (ex. DTS-CD) is input when "DEC. XXXX" in the CUSTOMIZE menu is set to "DEC. PCM". Set to "DEC. AUTO". PROTECT Irregular current is output from the speakers. The receiver will automatically turn off after a few seconds. Check the speaker connection and turn on the power again. If this problem persists, consult your nearest Sony dealer. If you are unable to remedy the problem using the troubleshooting guide Clearing the receiver's memory may remedy the problem (page 17). However, note that all memorized settings will be reset to their factory settings and you will have to readjust all settings on the receiver. If the problem persist Consult your nearest Sony dealer. Reference sections for clearing the receiver's memory To clear All memorized settings Customized sound fields See page 17 page 38 Specifications AUDIO POWER SPECIFICATIONS POWER OUTPUT AND TOTAL HARMONIC DISTORTION: (Models of area code U only) With 8 ohm loads, both channels driven, from 20 - 20,000 Hz; rated 90 watts per channel minimum RMS power, with no more than 0.09% total harmonic distortion from 250 milliwatts to rated output. Amplifier section Power Output Models of area code U, CA Rated Power Output at Stereo Mode (8 ohms 20 Hz - 20 kHz, THD 0.09%) 90 W + 90 W1) (8 ohms 1 kHz, THD 0.7%) 100 W + 100 W1) (8 ohms 1 kHz, THD 10%) 125 W + 125 W1) Reference Power Output1) (8 ohms 20 Hz - 20 kHz, THD 0.09%) FRONT2): 90 W/ch CENTER2): 90 W SURR2): 90 W/ch SURR BACK2): 90 W (8 ohms 1 kHz, THD 0.7%) FRONT2): 100 W/ch CENTER2): 100 W SURR2): 100 W/ch SURR BACK2): 100 W (8 ohms 1 kHz, THD 10%) FRONT2): 125 W/ch CENTER2): 125 W SURR2): 125 W/ch SURR BACK2): 125 W Models of area code CEL, CEK Rated Power Output at Stereo Mode (8 ohms 20 Hz - 20 kHz, THD 0.09%) 90 W + 90 W1) (8 ohms 1 kHz, THD 0.7%) 100 W + 100 W1) (8 ohms 1 kHz, THD 10%) 125 W + 125 W1) continued 51GB

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
51
GB
Additional Information
Error messages
If there is a malfunction, the display shows a
message. You can check the condition of the
receiver by the message. Refer to the following
table to solve the problem.
DEC. EROR
Appears when the signal which the receiver cannot
decode (ex. DTS-CD) is input when “DEC. XXXX”
in the CUSTOMIZE menu is set to “DEC. PCM”.
Set to “DEC. AUTO”.
PROTECT
Irregular current is output from the speakers. The
receiver will automatically turn off after a few
seconds. Check the speaker connection and turn on
the power again. If this problem persists, consult
your nearest Sony dealer.
If you are unable to remedy the
problem using the
troubleshooting guide
Clearing the receiver’s memory may remedy the
problem (page 17). However, note that all
memorized settings will be reset to their factory
settings and you will have to readjust all settings
on the receiver.
If the problem persist
Consult your nearest Sony dealer.
Reference sections for clearing
the receiver’s memory
AUDIO POWER SPECIFICATIONS
POWER OUTPUT AND TOTAL HARMONIC
DISTORTION:
(Models of area code U only)
With 8 ohm loads, both channels driven, from
20 – 20,000 Hz; rated 90 watts per channel
minimum RMS power, with no more than
0.09% total harmonic distortion from 250
milliwatts to rated output.
Amplifier section
Power Output
Models of area code U, CA
Rated Power Output at Stereo Mode
(8 ohms 20 Hz – 20 kHz, THD 0.09%)
90 W + 90 W
1)
(8 ohms 1 kHz, THD 0.7%)
100 W + 100 W
1)
(8 ohms 1 kHz, THD 10%)
125 W + 125 W
1)
Reference Power Output
1)
(8 ohms 20 Hz – 20 kHz, THD 0.09%)
FRONT
2)
:
90 W/ch
CENTER
2)
:
90 W
SURR
2)
:
90 W/ch
SURR BACK
2)
:
90 W
(8 ohms 1 kHz, THD 0.7%)
FRONT
2)
:
100 W/ch
CENTER
2)
:
100 W
SURR
2)
:
100 W/ch
SURR BACK
2)
:
100 W
(8 ohms 1 kHz, THD 10%)
FRONT
2)
:
125 W/ch
CENTER
2)
:
125 W
SURR
2)
:
125 W/ch
SURR BACK
2)
:
125 W
Models of area code CEL, CEK
Rated Power Output at Stereo Mode
(8 ohms 20 Hz – 20 kHz, THD 0.09%)
90 W + 90 W
1)
(8 ohms 1 kHz, THD 0.7%)
100 W + 100 W
1)
(8 ohms 1 kHz, THD 10%)
125 W + 125 W
1)
To clear
See
All memorized settings
page 17
Customized sound fields
page 38
Specifications
continued