Sony STR DG810 Instruction manual - Page 31

Confirming/saving the, measurement results, Confirm the measurement, result., Press RECEIVER and then - subwoofer

Get Sony STR DG810 - 6.1 Channel Home Theater Receiver PDF manuals and user guides
UPC - 027242705647
View all Sony STR DG810 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 31 highlights

Getting Started The table below shows the display when measurement starts. Measurement for Display Speaker existance Speaker gain, distance, frequency response Subwoofer gain and distance TONE T.S.P. WOOFER Note You cannot measure the speaker height of the surround speakers and the surround back speakers. Set this value using "SUR POS." parameters in the SYSTEM menu (page 42). Tips • The Auto Calibration function will be canceled when you do the following during the measurement process: - Press ?/1, input buttons or MUTING on the remote. - Press SPEAKERS (OFF/A/B/A+B) or turn the INPUT SELECTOR on the receiver. - Change the volume level. - Press AUTO CAL again. - Connect the headphones. • The measurement may not be performed correctly or Auto Calibration cannot be performed when special speakers, such as dipole speakers are used. Confirming/saving the measurement results 1 Confirm the measurement result. When the measurement ends, a beep sounds and the measurement result appears on the display. Measurement Display Explanation result When the measurement process completes properly SAVE Proceed to step 2. When the measurement process fails ERROR XXXX See "When error codes appear" (page 32). 2 Press RECEIVER and then press V/v repeatedly to select the item. Then, press . Item RETRY SAVE WARN CHK PHASE DISTANCE LEVEL EXIT Explanation Performs the Auto Calibration again. Saves the measurement results and exits the setting process. Displays warning concerning the measurement results. See "When you select "WARN CHK"" (page 32). Displays the phase of each speaker (in phase/out of phase). See "When you select "PHASE"" (page 33). Displays the measurement result for speaker distance. Displays the measurement result for speaker level. Exits the setting process without saving the measurement results. continued 31US

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
31
US
Getting Started
The table below shows the display when
measurement starts.
Note
You cannot measure the speaker height of the
surround speakers and the surround back speakers.
Set this value using “SUR POS.” parameters in the
SYSTEM menu (page 42).
Tips
• The Auto Calibration function will be canceled
when you do the following during the
measurement process:
– Press
?
/
1
, input buttons or MUTING on the
remote.
–
Press SPEAKERS (OFF/A/B/A+B) or turn the
INPUT SELECTOR on the receiver.
–
Change the volume level.
–
Press AUTO CAL again.
–
Connect the headphones.
• The measurement may not be performed correctly
or Auto Calibration cannot be performed when
special speakers, such as dipole speakers are used.
1
Confirm the measurement
result.
When the measurement ends, a beep
sounds and the measurement result
appears on the display.
2
Press RECEIVER and then
press
V
/
v
repeatedly to select
the item. Then, press
.
Measurement for
Display
Speaker existance
TONE
Speaker gain, distance,
frequency response
T.S.P.
Subwoofer gain and distance
WOOFER
Confirming/saving the
measurement results
Measurement
result
Display
Explanation
When the
measurement
process
completes
properly
SAVE
Proceed to step
2.
When the
measurement
process fails
ERROR
XXXX
See “When
error codes
appear” (page
32).
Item
Explanation
RETRY
Performs the Auto
Calibration again.
SAVE
Saves the measurement
results and exits the setting
process.
WARN CHK
Displays warning
concerning the
measurement results. See
“When you select “WARN
CHK”” (page 32).
PHASE
Displays the phase of each
speaker (in phase/out of
phase). See “When you
select “PHASE”” (page 33).
DISTANCE
Displays the measurement
result for speaker distance.
LEVEL
Displays the measurement
result for speaker level.
EXIT
Exits the setting process
without saving the
measurement results.
continued