Symphonic TVCR19G1 Owner's Manual - Page 10

Preparation

Get Symphonic TVCR19G1 PDF manuals and user guides View all Symphonic TVCR19G1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

PREPARATION FOR USE ENNA/CABLE - CONNECTIONS VHF'/C HE COMBINED /iNTENNA The VHF/UHF Rod Antenna (not supplied) is detachable. Push the stem of the antenna into the hole which is located on the upper back cabinet of the unit. Connect the VHF/UHF Rod Antenna or VHF/UHF Combination Antenna to the ANT. terminal of the TVNCR as shown in the diagram below. For the best reception, extend the VHF/UHF Rod Antenna fully and adjust its position. (Avoid handling the top section when making adjustments.) 1,1117/1411; SEPARATE ANTENNAS In some areas it will be necessary to use an outdoor antenna. VHF Antenna UHF Antenna VHF/UHF Combiner (Not a supplied) NOTE: ANT. gime Before plugging the Rod antenna into antenna terminal, check that the pin is not bent. If it is bent, straighten the pin as illustrated, then plug the pin into antenna terminal. Flat twin-lead cable Bent pin Cable Plug (Needs to be straightened) (Straight pin) VHF/UHF Antenna Rod Antenna (Not supplied) CABLE WITHOUT CONVERMR/ DESCRAMBLER BOX Use this connection if your cable system connects directly to your TV/VCR without a converter box. With this connection you, 1) can use your TVNCR Remote Control to select channels, 2) program one or more unscrambled channels for Automatic Timer Recording. From Cable System 75-ohm Coaxial Cable (not supplied) MEIN ANT. 0 O ANT. O Note to CATV system installer: This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building as close to the point of cable entry as practical. - 10 - EN 6L24

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
PREPARATION
FOR
USE
ENNA/CABLE
-
CONNECTIONS
VHF'/C
HE
COMBINED
/iNTENNA
The
VHF/UHF
Rod
Antenna
(not
supplied)
is
detach-
able.
Push
the
stem
of
the
antenna
into
the
hole
which
is
located
on
the
upper
back
cabinet
of
the
unit.
Connect
the
VHF/UHF
Rod
Antenna
or
VHF/UHF
Combination
Antenna
to
the
ANT.
terminal
of
the
TVNCR
as
shown
in
the
diagram
below.
For
the
best
reception,
extend
the
VHF/UHF
Rod
An-
tenna
fully
and
adjust
its
position.
(Avoid
handling
the
top
section
when
making
adjustments.)
NOTE:
Before
plugging
the
Rod
antenna
into
antenna
terminal,
check
that
the
pin
is
not
bent.
If
it
is
bent,
straighten
the
pin
as
illustrated,
then
plug
the
pin
into
antenna
terminal.
Bent
pin
Cable
Plug
(Needs
to
be
straightened)
(Straight
pin)
VHF/UHF
Antenna
Rod
Antenna
(Not
supplied)
MEIN
0
ANT.
O
1
,
111
7
/1411;
SEPARATE
ANTENNAS
In
some
areas
it
will
be
necessary
to
use
an
outdoor
an-
tenna.
VHF
Antenna
a
ANT.
gime
VHF/UHF
Combiner
(Not
supplied)
UHF
Antenna
Flat
twin
-lead
cable
CABLE
WITHOUT
CONVERMR/
DESCRAMBLER
BOX
Use
this
connection
if
your
cable
system
connects
di-
rectly
to
your
TV/VCR
without
a
converter
box.
With
this
connection
you,
1)
can
use
your
TVNCR
Re-
mote
Control
to
select
channels,
2)
program
one
or
more
unscrambled
channels
for
Automatic
Timer
Recording.
From
Cable
System
75
-ohm
Coaxial
Cable
(not
supplied)
ANT.
O
Note
to
CATV
system
installer:
This
reminder
is
provided
to
call
the
CATV
system
installer's
attention
to
Article
820-40
of
the
NEC
that
provides
guidelines
for
proper
grounding
and,
in
particular,
specifies
that
the
cable
ground
shall
be
connected
to
the
grounding
system
of
the
building
as
close
to
the
point
of
cable
entry
as
practical.
-
10
-
EN
6L24