TEAC W-860R Owners Manual - Page 8

Intro Check, Blank Scan, Multi-Counter

Page 8 highlights

Playback Intro Check This function can be used to search for a specific track by playing the beginning of each track for 15 seconds. Press the INTRO CHECK button. The deck will fast-wind to the beginning of a track, play the first 15 seconds (approx.), and fast-wind to the beginning of the next track, from which point the cycle starts again. ... If the play button of TAPE I is pressed during the Intro Check operation, playback will resume. ... If the STOP button is not pressed, the Intro Check function is released depending on the setting of the REV MODE switch. Ä: Released when tape reaches the end. Ë: Released when tape reaches the end of the reverse side. ä: Released after completing one full loop of the tape from the initial side. Play 15sec. ɹ 15sec. Fastforward Fastforward Tune Blank *More than approx. 4 seconds' blank needed. Multi-Counter Tape Counter Mode In this mode, the counter functions as a conventional tape counter, counting up when the tape is moving forward and down when the tape is being rewound. The display can be cleared by pressing the CLEAR button, which resets the counter index to "0000". Blank Scan This function is provided so that the deck will skip long blank portions during playback. 1. During playback, press the BLANK SCAN button (the indicator lights). If a blank section of more than about 10 seconds is detected during playback, the deck will enter the fast-forward mode automatically. When the beginning of the next recorded section is detected, playback will resume. 2. To release blank scan, press the BLANK SCAN button again (the indicator goes off). Notes: ... When the REV MODE switch is set to the Ë or ä position, the tape will be fast-forwarded at the end of either side of the tape after running the tape for 10 seconds without any sound. ... To check if the tape is entirely blank, start blank scan at the beginning of either side with the REV MODE switch set to the ä position. ... If there are sections of tape recorded at a low signal level, because of fading out, etc., these sections may be detected as blank and blank scan may start. In this case, the music will be interrupted for about 10 seconds. No sound for 10 seconds Play Tune Fast-forward Blank Play Tune Play Side A Side B Play No sound for 10 seconds Fast-forward Side B Start 8

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76

8
Intro Check
This function can be used to search for a specific track by
playing the beginning of each track for 15 seconds.
Press the INTRO CHECK button.
The deck will fast-wind to the beginning of a track, play the first
15 seconds (approx.), and fast-wind to the beginning of the
next track, from which point the cycle starts again.
If the play button of TAPE I is pressed during the Intro Check
operation, playback will resume.
If the STOP button is not pressed, the Intro Check function is
released depending on the setting of the REV MODE switch.
Ä
:
Released when tape reaches the end.
Ë
: Released when tape reaches the end of the
reverse side.
ä
: Released after completing one full loop of
the tape from the initial side.
Blank Scan
This function is provided so that the deck will skip long blank
portions during playback.
1. During playback, press the BLANK SCAN
button (the
indicator lights).
If a blank section of more than about 10 seconds is detected
during playback, the deck will enter the fast-forward mode
automatically. When the beginning of the next recorded
section is detected, playback will resume.
2. To release blank scan, press the BLANK SCAN button
again (the indicator goes off).
Notes:
When the REV MODE switch is set to the
Ë
or
ä
position, the tape will be fast-forwarded at the end of either
side of the tape after running the tape for 10 seconds
without any sound.
To check if the tape is entirely blank, start blank scan at the
beginning of either side with the REV MODE switch set to
the
ä
position.
If there are sections of tape recorded at a low signal level,
because of fading out, etc., these sections may be detected
as blank and blank scan may start. In this case, the music
will be interrupted for about 10 seconds.
Playback
Play
15sec.
15sec.
Fast-
forward
Fast-
forward
Blank
Tune
*More than approx.
4 seconds' blank needed.
No sound
for 10 seconds
No sound
for 10 seconds
Play
Play
Side A
Side B
Play
Play
Blank
Tune
Tune
Fast-forward
Fast-forward
Side B Start
Multi-Counter
Tape Counter Mode
In this mode, the counter functions as a conventional tape
counter, counting up when the tape is moving forward and
down when the tape is being rewound. The display can be
cleared by pressing the CLEAR button, which resets the counter
index to "0000".