TP-Link TL-WA801ND User Guide - Page 28

Network, TL-WA801ND, Network, Dynamic IP, Static IP, IP Address, Subnet Mask - default ip

Get TP-Link TL-WA801ND PDF manuals and user guides
UPC - 845973051419
View all TP-Link TL-WA801ND manuals
Add to My Manuals
Save this manual to your list of manuals

Page 28 highlights

TL-WA801ND 300Mbps Wireless N Access Point User Guide ) Note: The default PIN code of the AP can be found in its label or the QSS configuration screen as Figure 4-4. You will see the following screen when the new device has successfully connected to the network. ) Note: a. The QSS LED on the AP will light green for five minutes if the device has been successfully added to the network. b. The QSS function cannot be configured if the Wireless function of the AP is disabled. Please make sure the Wireless function is enabled before configuring the QSS. 4.4 Network The Network option allows you to customize your local network manually by changing the default settings of the AP. Selecting Network will enable you to configure the IP parameters of Network on this page. Figure 4-6 Network ¾ Type - Select Dynamic IP to get IP address from DHCP server or select Static IP to configure IP address manually from the drop-down list. ¾ IP Address - Enter the IP address of your AP in dotted-decimal notation (factory default setting is 192.168.1.254). ¾ Subnet Mask - An address code that determines the size of the network. Normally use 21

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
TL-WA801ND
300Mbps Wireless N Access Point User Guide
21
)
Note:
The default PIN code of the AP can be found in its label or the QSS configuration screen as Figure
4-4.
You will see the following screen when the new device has successfully connected to the network.
)
Note:
a.
The QSS LED on the AP will light green for five minutes if the device has been successfully
added to the network.
b.
The QSS function cannot be configured if the Wireless function of the AP is disabled. Please
make sure the Wireless function is enabled before configuring the QSS.
4.4
Network
The
Network
option allows you to customize your local network manually by changing the default
settings of the AP.
Selecting
Network
will enable you to configure the IP parameters of Network on this page.
Figure 4-6 Network
¾
Type -
Select
Dynamic IP
to get IP address from DHCP server or select
Static IP
to
configure IP address manually from the drop-down list.
¾
IP Address -
Enter the IP address of your AP in dotted-decimal notation (factory default
setting is 192.168.1.254).
¾
Subnet Mask -
An address code that determines the size of the network. Normally use