Toshiba TDP-TW90A Owners Manual - Page 36
Specifications Continued
View all Toshiba TDP-TW90A manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 36 highlights
Specifications (Continued) ■ List of supported signals (Y/PB/PR signals) Signal format 480i(525i)@60Hz 480p(525p)@60Hz 576i(625i)@50Hz 576p(625p)@50Hz 720p(750p)@60Hz 720p(750p)@50Hz 1080i(1125i)@60Hz 1080i(1125i)@50Hz 1035i(1125i)@60Hz 1152i(1250i)@50Hz fh(kHz) 15.73 31.47 15.63 31.25 45.00 37.50 33.75 28.13 33.75 31.25 fv(Hz) 59.94 59.94 50.00 50.00 60.00 50.00 60.00 50.00 60.00 50.00 ■ List of supported signals (Video, S-Video signals) Video mode NTSC PAL SECAM PAL-M PAL-N PAL-60 NTSC4.43 fh(kHz) 15.73 15.63 15.63 15.73 15.63 15.73 15.73 fv(Hz) 60 50 50 60 50 60 60 fsc(MHz) 3.58 4.43 4.25 or 4.41 3.58 3.58 4.43 4.43 ■ Pin assignment of COMPUTER-1/2 & MONITOR terminals 5 1 Pin Pin description No. During RGB input During Y/PB/PR input 1 Video signal (R) 2 Video signal (G) Color difference signal (PR) Luminance signal (Y) 10 6 15 11 Mini D sub 15 Pin connector 3 Video signal (B) 4 GND 5 GND 6 GND (R) 7 GND (G) Color difference signal (PB) ∗ ∗ GND (PR) GND (Y) Input Signal • RGB input 8 GND (B) 9 N.C GND (PB) ∗ RGB signals: 0.7V (p-p) 75 Ω 10 GND ∗ Horizontal sync signal: TTL level (Pos/neg polarity) 11 GND ∗ Vertical sync signal: TTL level (Pos/neg polarity) 12 N.C ∗ • Y/PB/PR input Y signal: PB/PR signals: 1.0V (p-p) 75 Ω 0.7V (p-p) 75 Ω 13 Horizontal sync signal ∗ 14 Vertical sync signal ∗ 15 N.C ∗ ∗ Do not connect anything. 70 ■ CONTROL terminal ● Pin assignment 7 8 6 5 3 4 21 Mini DIN 8 pin connector ● Interface format 1 Communication method 2 Communication format 3 Data format Pin No. 1 2 3 4 5 6 7 8 Signal Name RXD CTS DSR GND RTS N.C TXD GND Description Receiving data Consent to send Data set ready Signal ground Request to send No connection Sending data Signal ground RS-232C, 9600bps, No Parity, Data Length: 8 bits; Stop Bit Length: 1 bit STX (02h) Command (3Byte) ETX (03h) Only 1 command valid per communication. For input commands, only ASCII-compliant all-uppercase alphanumeric characters supported. 4 Replies Acknowledge ACK (06h) CR (0Dh) Data ... Normally ended ACK (06h) ESC (1Bh) ... Aborted No acknowledge NAK (15h) If commands are to be sent consecutively, wait for the response from the projector before sending the next command. ● Main Commands Item Power on Power off Icon display on Icon display off Auto setting (RGB input) Status display on Command PON POF MO0 MO1 PAT DON Item Computer (1) input select Computer (2) input select Video input select S-video input select PC card input select Command IN1 IN2 IN3 IN4 IN5 Status display off DOF Note • Contact your dealer for control cable and other commands. 71 Others