Toshiba W708 Owners Manual - Page 18

Storing Channels on the VCR continued, Adding or erasing channels, Selecting stored channels

Get Toshiba W708 PDF manuals and user guides View all Toshiba W708 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

Storing Channels on the VCR (continued) Adding or erasing channels Adding channels If a desired channel cannot be scanned automatically because of a weak signal, it can be added to the memory. Erasing channels You can erase a stored channel from the memory if it is unnecessary. 1) Follow steps 1 to 3 of "Incoming Antenna/CATV Signals". 2) Select "ADD CH" or "ERASE CH" using PLAY/X2 or STOP. To add channels PROGRAM SET UP PRESET TV / CATV AUTO SCAn ADD CH ERASE CH TV CATV OFF On - -On - -On TO SET CH PUSH 0~9 KEYS EnD: PROG To erase channels PROGRAM SET UP PRESET TV / CATV AUTO SCAn ADD CH ERASE CH TV CATV OFF On - -On - -On TO SET CH PUSH 0~9 KEYS EnD: PROG 3) Enter a channel number of 1 to 125 using number buttons. For more than 100 number, first press 100. For CATV channels, refer to the chart below. (For other orders, check with your cable company.) 4) Repeat steps 2) and 3) to add or erase channels as necessary. 5) Press PROG. to exit. Cable Box/DSS Output Channel Setting To set the Cable Box/DSS output Channel on the VCR. 1) Press PROG. to display the MENU screen. 2) Select "PRESET" using FF or REW, and press ENTER. 3) Select "CABLE BOX/DSS" using PLAY/X2 or STOP, and press ENTER. PROGRAM USE SET UP PRESET nO C . BOX DSS EnD: PROG 4) Select "NO", "C.BOX" or "DSS" using FF or REW according to your connection type. 5) If set to "C.BOX" or "DSS", select "OUTPUT CH" using PLAY/X2 or STOP. Then enter the output channel number of your cable box (Usually 3 or 4, check the rear of the cable box.) or line input mode "L1" using the I.SELECT button according to your connection. PROGRAM SET UP PRESET USE nO C . BOX DSS OUTPUT CH 3 CH TO SET CH PUSH 0~9 KEYS EnD: PROG 6) Press PROG. to exit. Selecting stored channels Once the active channels have been stored, you can select the channels in two ways below. Number buttons To enter digits of the channel number. • For one-digit number, enter 0 before. • For more than 100 number, first press 100. • Each number button needs to be pressed within 2 seconds. CH/TRK To shift up or down the stored channel numbers. 18

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
18
To add channels
To erase channels
Adding or erasing channels
Adding channels
If a desired channel cannot be scanned
automatically because of a weak signal, it can be
added to the memory.
Erasing channels
You can erase a stored channel from the memory
if it is unnecessary.
1)
Follow steps
1
to
3
of “Incoming Antenna/CATV
Signals”.
2)
Select “ADD CH” or “ERASE CH” using
PLAY/X2
or
STOP
.
3)
Enter a channel number of 1 to 125 using
number buttons
.
For more than 100 number, first press
100
.
For CATV channels, refer to the chart below.
(For other orders, check with your cable
company.)
4)
Repeat steps
2)
and
3)
to add or erase
channels as necessary.
5)
Press
PROG.
to exit.
Selecting stored channels
Once the active channels have been stored, you
can select the channels in two ways below.
Number buttons
To enter digits of the channel number.
•
For one-digit number, enter 0 before.
•
For more than 100 number, first press
100
.
• Each
number button
needs to be pressed
within 2 seconds.
CH/TRK
To shift up or down the stored channel numbers.
PROG
TV
TV
A
C
n
O
n
O
n
O
FF
O
O SET CH
PUSH
~9
0
EYS
K
T
––
––
TV/C
T
A
V
AUTO SCA
n
ADD
CH
ERAS
C
E
H
E D:
n
SET
UP
PRESET
PROGRAM
PROG
TV
TV
A
C
n
O
n
O
n
O
FF
O
O SET CH
PUSH
~9
0
EYS
K
T
––
––
TV/C
T
A
V
AUTO SCA
n
ADD
CH
ERAS
C
E
H
E D:
n
SET
UP
PRESET
PROGRAM
Storing Channels on the VCR (continued)
Cable Box/DSS Output Channel
Setting
To set the Cable Box/DSS output Channel on the
VCR.
1)
Press
PROG.
to display the MENU screen.
2)
Select “PRESET” using
FF
or
REW
, and press
ENTER
.
3)
Select “CABLE BOX/DSS” using
PLAY/X2
or
STOP
, and press
ENTER
.
4)
Select “NO”, “C.BOX” or “DSS” using
FF
or
REW
according to your connection type.
5)
If set to “C.BOX” or “DSS”, select “OUTPUT CH”
using
PLAY/X2
or
STOP
. Then enter the output
channel number of your cable box (Usually 3 or
4, check the rear of the cable box.) or line input
mode “L1” using the
I.SELECT
button according
to your connection.
6)
Press
PROG.
to exit.
PROG
C . BOX
O
n
S
S
D
USE
E D:
n
SET
UP
PRESET
PROGRAM
PROG
C . BOX
S
S
D
H
C
3
O SET CH
PUSH
~9
0
EYS
K
T
USE
OUT
UT
CH
P
E D:
n
SET
UP
PRESET
PROGRAM
O
n