ViewSonic PG706WU - 4000 Lumens WUXGA Projector with RJ45 LAN Control Vertical K - Page 33

Page 33 highlights

Operation Turning the Projector On/Off Starting Up the Projector 1. Press the Power button to turn on the projector. 2. The lamp will light up, and a "Power On/Off Ring Tone" will play. 3. The Power Indicator Light stays green when the projector is On. NOTE: • If the projector is still hot from previous use, it will run the cooling fan for 90 seconds before activating the lamp. • To maintain lamp life, once you turn the projector On, wait at least five (5) minutes before turning it off. 4. Turn on all of the connected equipment, i.e. notebook, and the projector will start to search for an input source. NOTE: If the projector detects an input source, the Source Selection Bar will appear. If an input source is not detected, the message, 'No Signal' will appear. First Time Activation If the projector is activated for the first time, select your OSD language following the on-screen instructions. 33

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
33
Operation
Turning the Projector On/Off
Starting Up the Projector
1.
Press the
Power
bu²on to turn on the projector.
2.
The lamp will light up, and a
“Power On/Off Ring Tone”
will play.
3.
The Power Indicator Light stays green when the projector is On.
NOT±:
•
If the projector is s°ll hot from previous use, it will run the cooling fan for 90
seconds before ac°va°ng the lamp.
•
To maintain lamp life, once you turn the projector On, wait at least five (5)
minutes before turning it off.
4.
Turn on all of the connected equipment, i.e. notebook, and the projector will
start to search for an input source.
NOT±:
If the projector detects an input source, the Source Selec°on Bar will appear. If
an input source is not detected, the message, ‘No Signal’ will appear.
First Time Activation
If the projector is activated for the first time, select your OSD language following
the on-screen instructions.