Weider 3550 User Manual - Page 17

Attach the Pulley and a Cable Trap 68

Get Weider 3550 PDF manuals and user guides View all Weider 3550 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

40. Wrap the VKR Low Cable (72) under a 3 1/2" 40 Pulley (78). Attach the Pulley to the indicated brack- et on the Long Base (120) with a 3/8" x 1 3/4" Bolt (93) and a 3/8" Nylon Locknut (87). 78 72 87 93 120 41. Route the VKR Low Cable (72) under the indicated 41 stack of Weights (44). Wrap the VKR Low Cable (72) under a 3 1/2" 44 Pulley (78). Attach the Pulley to the indicated brack- et on the Long Base (120) with a 3/8" x 1 3/4" Bolt (93) and a 3/8" Nylon Locknut (87). 78 72 87 42. Wrap the VKR Low Cable (72) over a 3 1/2" Pulley 42 (78). Attach the Pulley and a Cable Trap (68) between the indicated holes in the Pulley Plates (63) with a 3/8" x 2" Bolt (100) and a 3/8" Nylon Locknut (87). Make sure that the Cable Trap is turned to hold the Cable in the groove of the Pulley. 93 120 100 63 68 87 72 78 43. Wrap the VKR Low Cable (72) under a 3 1/2" 43 Pulley (78). Attach the Pulley to the indicated brack- et on the Short Base (2) with a 3/8" x 1 3/4" Bolt (93) and a 3/8" Nylon Locknut (87). 17 78 87 72 2 93

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
17
40. Wrap the VKR Low Cable (72) under a 3 1/2”
Pulley (78). Attach the Pulley to the indicated brack-
et on the Long Base (120) with a 3/8” x 1 3/4” Bolt
(93) and a 3/8” Nylon Locknut (87).
41. Route the VKR Low Cable (72) under the indicated
stack of Weights (44).
Wrap the VKR Low Cable (72) under a 3 1/2”
Pulley (78). Attach the Pulley to the indicated brack-
et on the Long Base (120) with a 3/8” x 1 3/4” Bolt
(93) and a 3/8” Nylon Locknut (87).
42. Wrap the VKR Low Cable (72) over a 3 1/2” Pulley
(78). Attach the Pulley and a Cable Trap (68)
between the indicated holes in the Pulley Plates
(63) with a 3/8” x 2” Bolt (100) and a 3/8” Nylon
Locknut (87).
Make sure that the Cable Trap is
turned to hold the Cable in the groove of the
Pulley.
43. Wrap the VKR Low Cable (72) under a 3 1/2”
Pulley (78). Attach the Pulley to the indicated brack-
et on the Short Base (2) with a 3/8” x 1 3/4” Bolt
(93) and a 3/8” Nylon Locknut (87).
43
40
41
42
93
78
120
72
87
93
120
72
78
87
44
72
68
100
63
2
72
93
87
78
78
87