Weider E2000 English Manual - Page 14

Seat Assembly

Get Weider E2000 PDF manuals and user guides View all Weider E2000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

30. Wrap the Low Cable (9) around a 3 1/2Ó Pulley (35) in 30 the direction shown. Attach the Pulley to the Front 42 Upright (42) with a 3/8Ó x 3 3/4Ó Bolt (19), a Cable Trap (66), a 3/8Ó Flat Washer (55), and a 3/8Ó Nylon Jamnut (63). 63 35 55 Make sure the Cable Trap (66) is positioned as shown and that the Pulley (35) is not rubbing on the Cable Trap. Attach the loop on the end of the Low Cable (9) to the 19 66 3/8Ó x 2 1/4Ó Eyebolt (44) with a Cable Clip (73). Note: Cable Clips are located in the parts bag labeled ÒSEAT ASSEMBLY.Ó 12 Seat Assembly 31 9 73 44 31. Open the parts bag labeled ÒSEAT ASSEMBLY.Ó Attach the Backrest (41) to the Front Upright (42) with two 1/4Ó x 2 1/2Ó Screws (43) and two 1/4Ó Flat 42 Washers (90). 43 90 41 43 32. Insert the 1/4Ó x 2Ó Carriage Bolt (38) into the center 32 hole in the Seat Plate (37). Attach the Seat Plate to the Seat (13) with two 1/4Ó x 3/4Ó Screws (17). Insert the 1/4Ó x 2Ó Carriage Bolt (38) into the indicated hole in the Seat Frame (36). Tighten a 1/4Ó Nylon Locknut (89) with a 1/4Ó Flat Washer (90) onto the Carriage Bolt. Attach the other end of the Seat (13) to the Seat Frame (36) with a 1/4Ó Flat Washer (90) and a 1/4Ó x 2Ó Bolt (71). 14 13 38 36 37 17 90 90 71 89

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
31.
Open the parts bag labeled ±SEAT ASSEMBLY.²
Attach the Backrest (41) to the Front Upright (42) with
two 1/4± x 2 1/2± Screws (43) and two 1/4± Flat
Washers (90).
Seat Assembly
41
43
43
90
42
30.
Wrap the Low Cable (9) around a 3 1/2± Pulley (35) in
the direction shown. Attach the Pulley to the Front
Upright (42) with a 3/8± x 3 3/4± Bolt (19), a Cable
Trap (66), a 3/8± Flat Washer (55), and a 3/8± Nylon
Jamnut (63).
Make sure the Cable Trap (66) is positioned as
shown and that the Pulley (35) is not rubbing on
the Cable Trap.
Attach the loop on the end of the Low Cable (9) to the
3/8± x 2 1/4± Eyebolt (44) with a Cable Clip (73).
Note: Cable Clips are located in the parts bag labeled
²SEAT ASSEMBLY.±
30
12
9
73
44
19
66
35
42
63
55
32.
Insert the 1/4± x 2± Carriage Bolt (38) into the center
hole in the Seat Plate (37). Attach the Seat Plate to
the Seat (13) with two 1/4± x 3/4± Screws (17).
Insert the 1/4± x 2± Carriage Bolt (38) into the indicat-
ed hole in the Seat Frame (36). Tighten a 1/4± Nylon
Locknut (89) with a 1/4± Flat Washer (90) onto the
Carriage Bolt.
Attach the other end of the Seat (13) to the Seat
Frame (36) with a 1/4± Flat Washer (90) and a 1/4± x
2± Bolt (71).
32
37
17
90
36
13
38
90
71
14
31
89