Weslo Gym 3000 Uk Manual - Page 11

Thread the Nylon Locknut

Get Weslo Gym 3000 PDF manuals and user guides View all Weslo Gym 3000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

18. Remove the 3/8" x 1 3/4" Bolt (48), 3/8" Nylon Locknut (21), and 3 1/2" Pulley (15) from the indicated bracket on the Top Frame (67). Insert the end of the Long Cable (66) through the bracket and down through the indicated hole. Reattach the 3 1/2" Pulley (15) to the bracket on the Top Frame (67) with the 3/8" x 1 3/4" Bolt (48) and 3/8" Nylon Locknut (21). Make sure that the Long Cable is between the Pulley and the top of the bracket. 18 Bracket Hole 67 21 15 66 48 19. Remove the 3/8" Nylon Locknut (21), 3/8" x 1 3/4" Bolt (48), and 4 1/2" Pulley (77) from one end of the "I" Plates (78). Route the Long Cable (66) under the Pulley and reattach the Pulley to the "I" Plates with the Bolt and Nylon Locknut. Refer to the inset drawing. (Note: The Wide Swivel Bracket [71] is attached to the Top Frame [67]; it is shown disassembled for clarity.) Lay the Long Cable (66) over a 3 1/2" Pulley (15). Attach the Pulley and a Cable Trap (59) to the Wide Swivel Bracket (71) with a 3/8" x 1 3/4" Bolt (48) and 3/8" Nylon Locknut (21). Make sure that the Cable Trap is turned to the indicated position. 20. Wrap the Long Cable (66) down around the 3 1/2" Pulley (15) on the left Arm (46). Tighten the 3/8" Nylon Locknut (21) and 3/8" x 1 3/4" Bolt (not shown). Make sure that the Cable Trap (59) is turned to the indicated position. 19 67 66 77 21 20 48 71 15 59 21 66 48 78 15 66 21 46 59 21. Note: The 4 1/2" Pulley (77) shown in this step is preattached to the Adjustment "U" Bracket (75). Attach the Adjustment "U" Bracket to the Front Upright (42) with the 5/16" x 3 1/4" Special Tread Bolt (105), a 5/16" Flat Washer (8), and a 5/16" Nylon Locknut (3). Thread the Nylon Locknut onto the Bolt only two complete turns. Remove the 3/8" x 1 3/4" Bolt (48), 3/8" Nylon Locknut (21), and 4 1/2" Pulley (77) from the Adjustment "U" Bracket (75). Wrap the Long Cable (66) around the Pulley as shown. Reattach the Pulley to the Adjustment "U" Bracket with the Bolt and Nylon Locknut. 21 3 8 42 11 48 75 21 105 66 77

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
11
18. Remove the 3/8” x 1 3/4” Bolt (48), 3/8” Nylon
Locknut (21), and 3 1/2” Pulley (15) from the indi-
cated bracket on the Top Frame (67). Insert the
end of the Long Cable (66) through the bracket
and down through the indicated hole.
Reattach the 3 1/2” Pulley (15) to the bracket on
the Top Frame (67) with the 3/8” x 1 3/4” Bolt (48)
and 3/8” Nylon Locknut (21).
Make sure that the
Long Cable is between the Pulley and the top
of the bracket.
19. Remove the 3/8” Nylon Locknut (21), 3/8” x 1 3/4”
Bolt (48), and 4 1/2” Pulley (77) from one end of
the “I” Plates (78). Route the Long Cable (66)
under the Pulley and reattach the Pulley to the “I”
Plates with the Bolt and Nylon Locknut.
Refer to the inset drawing. (Note: The Wide
Swivel Bracket [71] is attached to the Top Frame
[67]; it is shown disassembled for clarity.) Lay the
Long Cable (66) over a 3 1/2” Pulley (15). Attach
the Pulley and a Cable Trap (59) to the Wide
Swivel Bracket (71) with a 3/8” x 1 3/4” Bolt (48)
and 3/8” Nylon Locknut (21).
Make sure that the
Cable Trap is turned to the indicated position.
20. Wrap the Long Cable (66) down around the 3 1/2”
Pulley (15) on the left Arm (46). Tighten the 3/8”
Nylon Locknut (21) and 3/8” x 1 3/4” Bolt (not
shown).
Make sure that the Cable Trap (59) is
turned to the indicated position.
21. Note: The 4 1/2” Pulley (77) shown in this step is
preattached to the Adjustment “U” Bracket (75).
Attach the Adjustment “U” Bracket to the Front
Upright (42) with the 5/16” x 3 1/4” Special Tread
Bolt (105), a 5/16” Flat Washer (8), and a 5/16”
Nylon Locknut (3).
Thread the Nylon Locknut
onto the Bolt only two complete turns.
Remove the 3/8” x 1 3/4” Bolt (48), 3/8” Nylon
Locknut (21), and 4 1/2” Pulley (77) from the
Adjustment “U” Bracket (75). Wrap the Long
Cable (66) around the Pulley as shown. Reattach
the Pulley to the Adjustment “U” Bracket with the
Bolt and Nylon Locknut.
20
19
48
48
71
77
78
15
59
21
21
46
15
77
105
21
75
48
66
3
8
42
66
21
59
66
67
66
18
67
Bracket
Hole
66
21
15
48
21