Weslo Gym 3000 Uk Manual - Page 7

Nylon Locknuts yet.

Get Weslo Gym 3000 PDF manuals and user guides View all Weslo Gym 3000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 7 highlights

4. Press two 2" Inner Caps (27) into the Top Frame (67). Attach the Top Frame (67) to the Front Upright (42) and to the Rear Upright (82) with two 5/16" x 2 3/4" Bolts (11), 5/16" Flat Washers (8), and 5/16" Nylon Locknuts (3). Do not tighten the Nylon Locknuts yet. Attach the Top Frame (67) to the Stop Bracket (63) with a 5/16" x 2 3/4" Bolt (11), 5/16" Flat Washer (8), and 5/16" Nylon Locknut (3). Do not tighten the Nylon Locknut yet. Tighten all Nylon Locknuts used in steps 2 through 4. 5. Press two 1 1/2" Bushings (93) into the Left Pedal (90); press two 1 1/2" Bushings (93) into the Right Pedal (89). Attach a Pedal Cover (92) to each Pedal with a 1/2" Tap Screw (6). Lubricate the pedal axles on the Rear Upright (82). Slide the Right and Left Pedals (89, 90) onto the right and left pedal axles. Note: Make sure that the Pedals are on the correct sides; the slotted brackets must be on the insides of the Pedals. Hold a 1" Retainer (54) and 1" Round Cover Cap (55) against the left pedal axle. The teeth on the Retainer must bend toward the Round Cover Cap. Tap the Retainer and Round Cover Cap onto the pedal axle. Attach the Right Pedal in the same manner. 6. Lubricate the cylinder axles on the Rear Upright (82). Slide a 5/8" Spacer (97) and a Resistance Cylinder (91) onto the right cylinder axle. Make sure that the Spacer is turned as shown. Hold a 5/8" Retainer (95) and 5/8" Round Cover Cap (96) against the right cylinder axle. The teeth on the Retainer must bend toward the Round Cover Cap. Tap the Retainer and Round Cover Cap onto the cylinder axle. Attach a Resistance Cylinder (91) to the left cylinder axle in the same manner. 4 11 8 11 8 11 8 67 27 3 3 82 42 3 27 63 5 92 6 6 92 89 93 82 Lubricate Slotted Brackets 90 54 93 55 6 96 95 97 82-Lubricate 91 7. Raise the Left Pedal (90) and rest it on the hook at the lower end of the left Resistance Cylinder 7 (91). The hook must be in one of the slots under the Left Pedal. Raise the Right Pedal (89) and rest it on the hook at the lower end of the right Resistance Cylinder (91). Make sure that the hooks are in the same position under both Pedals. 91 89 Hooks 90 7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
7
4.
Press two 2” Inner Caps (27) into the Top Frame
(67). Attach the Top Frame (67) to the Front
Upright (42) and to the Rear Upright (82) with two
5/16” x 2 3/4” Bolts (11), 5/16” Flat Washers (8),
and 5/16” Nylon Locknuts (3).
Do not tighten the
Nylon Locknuts yet.
Attach the Top Frame (67) to the Stop Bracket
(63) with a 5/16” x 2 3/4” Bolt (11), 5/16” Flat
Washer (8), and 5/16” Nylon Locknut (3).
Do not
tighten the Nylon Locknut yet.
Tighten all Nylon Locknuts used in steps 2
through 4.
5.
Press two 1 1/2” Bushings (93) into the Left Pedal
(90); press two 1 1/2” Bushings (93) into the
Right Pedal (89). Attach a Pedal Cover (92) to
each Pedal with a 1/2” Tap Screw (6).
Lubricate the pedal axles on the Rear Upright
(82). Slide the Right and Left Pedals (89, 90) onto
the right and left pedal axles.
Note: Make sure
that the Pedals are on the correct sides; the
slotted brackets must be on the insides of the
Pedals.
Hold a 1" Retainer (54) and 1" Round
Cover Cap (55) against the left pedal axle.
The
teeth on the Retainer must bend toward the
Round Cover Cap.
Tap the Retainer and Round
Cover Cap onto the pedal axle. Attach the Right
Pedal in the same manner.
6.
Lubricate the cylinder axles on the Rear Upright
(82). Slide a 5/8” Spacer (97) and a Resistance
Cylinder (91) onto the right cylinder axle.
Make
sure that the Spacer is turned as shown.
Hold
a 5/8" Retainer (95) and 5/8" Round Cover Cap
(96) against the right cylinder axle.
The teeth on
the Retainer must bend toward the Round
Cover Cap.
Tap the Retainer and Round Cover
Cap onto the cylinder axle.
Attach a Resistance Cylinder (91) to the left cylin-
der axle in the same manner.
7.
Raise the Left Pedal (90) and rest it on the hook
at the lower end of the left Resistance Cylinder
(91). The hook must be in one of the slots under
the Left Pedal.
Raise the Right Pedal (89) and rest it on the hook
at the lower end of the right Resistance Cylinder
(91).
Make sure that the hooks are in the same
position under both Pedals.
7
5
6
92
92
6
6
55
54
90
89
96
95
91
97
82—Lubricate
91
90
89
Hooks
82
Lubricate
93
93
Slotted
Brackets
4
27
27
67
42
11
8
3
11
8
3
63
11
82
8
3