Whirlpool DP840SWSX Use and Care Guide - Page 9

Connecting to Water and Electrical Supply, Using the Faucet, Disconnecting the Dishwasher - faucet adapter

Get Whirlpool DP840SWSX - 24inchPortable Dishwasher, 5 Cycles PDF manuals and user guides
UPC - 883049042909
View all Whirlpool DP840SWSX manuals
Add to My Manuals
Save this manual to your list of manuals

Page 9 highlights

Connecting the faucet adapter to faucets with internal threads Insert the 2 screens, the thin washer, and then the thick washer from the faucet adapter kit into the faucet adapter. Attach the adapter onto the end of the faucet. NOTE: Use both washers. A B C D A. Thick washer B. Thin washer C. Screens D. Faucet adapter Connecting to Water and Electrical Supply 1. Run water at the faucet until it is hot. Turn off the water. 2. Pull the hoses out of their storage compartment on the back of the dishwasher. NOTE: Make sure the hoses are not kinked or twisted. Kinked hoses reduce washing performance. 3. Pull down on the locking collar while lifting the hose connector onto the faucet adapter. A B C A. Faucet adapter B. Locking collar C. Hose connector 4. When the connector snaps into place, release the locking collar. 5. Turn the hot water on slowly until it is all the way on. 6. Plug into a grounded 3 prong outlet. Using the Faucet You can draw water from the faucet while the dishwasher is connected. NOTE: Do not draw water while the dishwasher is filling or while water is being pumped out. (This helps avoid a low fill when dishwasher is filling or mixing drain water with fresh water when dishwasher is draining.) Press the red button on the hose connector to draw water from the faucet. (The faucet is set on hot. Adjust the faucet for the water temperature you want.) NOTE: Turn the hot water back on after you draw water from the faucet. Turn off the cold water. Disconnecting the Dishwasher 1. Turn off the hot water. (This can be done after the last rinse.) 2. Press the red button on the connector to release the water pressure. A B C D A. Faucet adapter B. Locking collar C. Red button D. Hose connector 3. Lift slightly on the hose connector while pulling down the locking collar. Pull down on the connector. 4. Empty any remaining water from the connector by turning the connector upside-down. 5. Unplug the power supply cord and return it to the storage compartment. 6. Return the hoses to the storage compartment. 9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
9
Connecting the faucet adapter to faucets with
internal threads
Insert the 2 screens, the thin washer, and then the thick washer
from the faucet adapter kit into the faucet adapter. Attach the
adapter onto the end of the faucet.
NOTE:
Use both washers.
Connecting to Water and Electrical Supply
1.
Run water at the faucet until it is hot. Turn off the water.
2.
Pull the hoses out of their storage compartment on the back
of the dishwasher.
NOTE:
Make sure the hoses are not kinked or twisted. Kinked
hoses reduce washing performance.
3.
Pull down on the locking collar while lifting the hose
connector onto the faucet adapter.
4.
When the connector snaps into place, release the locking
collar.
5.
Turn the hot water on slowly until it is all the way on.
6.
Plug into a grounded 3 prong outlet.
Using the Faucet
You can draw water from the faucet while the dishwasher is
connected.
NOTE:
Do not draw water while the dishwasher is filling or while
water is being pumped out. (This helps avoid a low fill when
dishwasher is filling or mixing drain water with fresh water when
dishwasher is draining.)
Press the red button on the hose connector to draw water from
the faucet. (The faucet is set on hot. Adjust the faucet for the
water temperature you want.)
NOTE:
Turn the hot water back on after you draw water from the
faucet. Turn off the cold water.
Disconnecting the Dishwasher
1.
Turn off the hot water. (This can be done after the last rinse.)
2.
Press the red button on the connector to release the water
pressure.
3.
Lift slightly on the hose connector while pulling down the
locking collar. Pull down on the connector.
4.
Empty any remaining water from the connector by turning the
connector upside-down.
5.
Unplug the power supply cord and return it to the storage
compartment.
6.
Return the hoses to the storage compartment.
A. Thick washer
B. Thin washer
C. Screens
D. Faucet adapter
A. Faucet adapter
B. Locking collar
C. Hose connector
A
B
C
D
A
B
C
A. Faucet adapter
B. Locking collar
C. Red button
D. Hose connector
A
B
C
D